串行EPROM的内容。
These sockets are used in EPROM programmers, burn-in boards and test jigs.
这些插座在EPROM编程器、老化板和测试夹具中使用。
Once erased, an EPROM can be reprogrammed with the help of a device programmer.
一次擦除后，EPROM可以在设备编程器的帮助下被重编程。
Once erased an EPROM can be reprogrammed with the help of a device programmer.
一次擦除后，EPROM可以在设备编程器的帮助下被重编程。
To Embed the control program debugged successfully into EPROM, and debug the system on EPROM;
把仿真调试成功的控制程序烧入EPROM芯片，进行EPROM仿真调试；
This text introduces a method about designing an automatic pad-printing machine based on EPROM.
介绍了采用数字逻辑方法，用EPROM存储器为核心设计自动移印机。
The voltage output is supplied to a load, for example, the word line of an EPROM memory circuit.
将电压输出供应到负载，例如EPROM存储器电路的字线。
A circuit for writing EPROM and an all software cassette tape recording scheme are also introduced.
最后还介绍了一种EPROM写入电路及一种全软件式盒式磁带记录方案。
The article gives the principle, method and applied example of the EPROM used as sequential circuit design.
介绍了用EPROM进行时序电路设计的原理、方法和应用实例。
This paper describes the mechanism of an EPROM (erasible programmable read-only memory) and the fast-writing mode.
本文论述EPROM（可擦除可编程序只读存贮器）的机制和快写方法。
This discourse introduces the method of how to design time controller circuit by assembling EPROM programmable memory.
文章介绍了利用EPROM可编程存贮的特性来设计定时控制电路的方法。
For example, program voltage levels used in EPROM and flash memory circuits are higher than the voltages normally used in memory circuits.
举例来说，在EPROM和快闪存储器电路中使用的编程电压电平高于存储器电路中通常使用的电压。
The bootable image is created along with interfaces with the server's boot Read-Only Storage (ROS) and Erasable Programmable Read-Only Memory (EPROM).
可启动映像以及一些接口是通过服务器的启动只读存储器(ROS)和可擦可编程只读存储器(EPROM)创建的。
This paper introduces the FLASH MEMORY circuits technique and structure characteristic, also compared the circuits with that of EPROM and EEPROM.
本文介绍了闪速存储器的结构特点和工艺技术，并与EPROM和EEP - ROM电路进行了比较。
It's a new technology in the design of microcomputer-based system to embed the high-level language programs into EPROM for the dedicated microcomputer systems.
把用高级语言编写的应用程序嵌入专用微处理器系统，是微机化系统设计中的一个新技术。
A microcontroller requests a flexible configuration of FPGA in some special project applications, usually it cannot be satisfied by routine EPROM configuration.
微控制器在某些工程应用中经常需要对FPGA进行灵活的配置，采用常规的EPROM配置FPGA很难满足这一要求。
In this way we can take good advantage of the storage location of the residual division in EPROM omit the facility of decoders and decrease the rate of the error.
这样做可以充分利用EPROM中剩余部分的存储单元，省略译码器设备，减少出错几率。
This paper describes a method to realize automatic switching and control in direct news broadcasting by means of EPROM. The design and circuit implementation is also given.
介绍了一种用eprom可编程器件实现新闻直播自动切换控制的方法，并给出了具体的设计和实现电路。
EPROM: in full erasable programmable read-only memory, Form of computer memory that does not lose its content when the power supply is cut off and that can be erased and reused.
可抹除可程序化只读存储器：计算机内存的形式，切断电源供应之后内容不会消失，并且可以删除及重复利用。
A new method of nonlinear correction based on EPROM is introduced. According to it, an instrument with high precision and low cost and wide use to measure temperature is constituted.
针对热电偶的非线性严重影响测温精度，本文提出一种利用EPROM器件进行非线性校正的新方法，并据此构成一种适用广、精度高、成本低的热电偶测温仪。
The principle of voltage linear digital triggering of thyristor by EPROM is described and it is discussed to solve the frequency disturbance on digital trigger by phase locked loop .
描述了用EPROM实现晶闸管电压线性触发原理，讨论了用锁相环解决数字触发的频率扰动问题。
EPROM (Erasable programming Read Only Memory) programming device is depicted; its system configuration, operation principle, software design and some flow charts are stated accordingly.
设种通eprom(擦编程序读存储器)程器，阐述该编程器系统、软件设，程序设流程图。
Each of the right and left charge storage regions are capable of storing one-bit of information, which can be programmed and read through minimal adaptation of standard EPROM techniques.
每个右和左电荷存储区都能够存储一位信息，此信息可以通过标准EPROM技术的微小调整来编程和读取。
The passive serial configuration of FPGA is controlled by CPLD. EPROM is selected to store the configuration program. It can improve encryption of the CNC system, and simplify the circuit.
该方法由CPLD控制配置过程，EPROM存储配置文件，实现了FPGA的被动串行配置，增强了数控系统的保密性、简化了系统电路。
The passive serial configuration of FPGA is controlled by CPLD. EPROM is selected to store the configuration program. It can improve encryption of the CNC system, and simplify the circuit.
该方法由CPLD控制配置过程，EPROM存储配置文件，实现了FPGA的被动串行配置，增强了数控系统的保密性、简化了系统电路。
应用推荐