That sound you hear may be the gears of the industrial marketing engine turning a bit faster compared to recent years.
您似乎已经听到了今年工业营销“发动机”上的“齿轮”，与近几年相比要转得更快。
In the early days of cars, you actually had to crank the engine with a little handle. Now the cranking motor or starter is just powerful enough to start the engine turning.
以前的汽车需使摇柄才能使发动机启动，现在启动机或点火机已足以使发动机启动了。
But instead of just sticking to the dull but profitable business of keeping the engine of Germany's economy turning, IKB turned its hand to dabbling in America's housing markets.
但是代替这种愚钝行为的是以完全盈利的产业作为德国经济扭转的引擎，IKB就已开始涉足美国的住房市场。
Wallis said:" They are one of the safest machines to fly because, if the engine stops, the rotors keep turning and you can land."
沃利斯称：“驾驶旋翼飞机很安全，即使引擎停转，旋翼还会继续转动，所以可以安全着地。”
He is turning the engine over.
他正在发动引擎。
After 40 miles, a gasoline engine starts turning a generator to make electricity for the motor.
40英里之后，汽油发动机开始驱动发电机发电，给发动机提供电力。
Stay visible by putting bright cloth on the antenna, turning on the inside overhead light (when engine is running), and raising the hood when snow stops falling.
在天线上覆盖明亮的布确保可见，打开内部的头顶灯（当引擎发动时），同时当雪停时掀起发动机罩。
If you're going to idle your car for more than a minute, it's worth turning off the engine.
如果你要停车超过一分钟，就需要关闭引擎。
CASCADE vane, a vane for turning the engine airflow during operation of thrust reverser.
叶栅叶片，在反推工作时，使发动机气流向相反方向流动的叶片。
Then turning to the pits I was on the white paint while breaking with engine.
然后在转向维修站时我加了油门，驶上了白色的油漆。
After turning off the engine, wait for at least 5 minutes for the oil to drain back into the bottom of the engine.
在发动机熄火后，为了让机油流回发动机底部，至少要等5分钟。
At the same time, because of structural limitations, steering pump on a typical installation in the vehicle next to the engine, the ambient temperature very high, thus turning more serious heat pump.
同时，由于受结构的限制，转向液压泵在整车上一般安装于发动机旁，环境温度很高，因而转向液压泵发热更为严重。
In this paper some overall plans of turning device for machining diesel engine block are discussed and their behaviours are compared.
本文提出了几种柴油机机体加工翻转台的新方案，并对这些方案的性能作了比较。
The engine crankshaft can then turn without turning the clutchdisc and the transmission input shaft.
之后发动机曲轴转动起来，不需离合器和变速器输人轴的转动。
Particularly practise turning the engine off promptly.
尤其是迅速关闭发动机。
For your safety, never approach turning parts, such as fan, belt to avoid cutting, high temperature parts as exhaust pipe, turbo-charger, muffler and radiator to avoid burn when engine is running.
为了您的安全，柴油机在运转时禁止靠近风扇、皮带等旋转部位以免打伤，排气管、增压器、消声器、散热器等高温部位在靠近时防止烫伤。
Revving the engine before turning it off may reduce fuel economy.
在发动机未关闭时空踩油门会降低燃油经济性。
I choose a wrong turning direction as the engine failed on the crosswind.
在二边发动机失效的情况下，选择了错误的转弯方向。
The fluid exits the turbine moving opposite the direction that the pump and engine are turning.
流体出口涡轮移动相反的方向表示，该泵和发动机的转折。
The way to get really big returns is to do things that seem crazy, like starting a new search engine in 1998, or turning down a billion dollar acquisition offer.
得到大笔回报的方法，就是去做那些看上去很疯狂的事情，比如1998年的时候开办一家新的搜索引擎，或者拒绝一笔10亿美元的并购报价。
There is AC request switch on instrument panel; the controller will control the engine and keep it running smoothly once the controller receives the request signal of AC turning on.
在车辆的仪表盘上有空调请求开关，一旦控制器接收到空调打开的请求信号，控制器将对发动机进行控制并保持正常运行。
The hydraulic turning system can make turning by hand after the engine flameout.
转向系统为液压动力，操作轻便，即使熄火也能用手进行转向。
MANEUVERABILITY. Short turning radius. Rear engine, less weight on front.
较小的转弯半径，发动机后置，前部较轻重量。
But unlike existing hybrids such as the Toyota Prius in which the petrol engine drives the car directly these so-called plug-in hybrids are pure-electric vehicles when it comes to turning the wheels.
但与丰田普锐斯等现有的直接由汽油启动的混合动力汽车不同，这些所谓的“插件式”混合动力汽车在启动时都是由纯电力驱动的。
The design of copying wheel is given too. Combined microcomputer control and hydraulic copying technique, an engine lathe is retro fitted into an automatic lathe to turning such kind of workpiece.
这种加工方法采用微机控制技术和液压仿形技术相结合对普通车床进行改造，实现自动加工。
The design of copying wheel is given too. Combined microcomputer control and hydraulic copying technique, an engine lathe is retro fitted into an automatic lathe to turning such kind of workpiece.
这种加工方法采用微机控制技术和液压仿形技术相结合对普通车床进行改造，实现自动加工。
应用推荐