Based on completion of wall strength calculation, then do the finite element stress analysis.
在完成管壁强度计算的基础上，进行管壁有限元应力分析。
Based on the broken gear teeth in contact fatigue test, bending fatigue life curve was got by applying finite element stress analysis results, MSC.
本文以接触疲劳试验中疲劳断齿齿轮为依据，利用有限元应力分析结果以及试验得到的弯曲疲劳寿命曲线，应用msc。
The integrated finite element stress analysis for a bladed disk assembly has been carried out, using the cyclic symmetric model with contact surfaces.
本文用含接触面的循环对称计算模型进行轮盘-叶片组件的统一有限无应力分析。
The three dimensional finite element stress analyses of main girder with twin-box cross section used commonly in cable-stayed bridge have been carried out.
本文对斜拉桥双箱单室箱形主梁进行了空间有限元应力分析。
This article uses the ANSYS software and analysis design method to make a detailed finite element stress analysis of the head of valve body where placed the quarter rings.
利用ANSYS软件及其分析设计方法，对阀体中腔安装四合环的位置进行了有限元应力分析。
The satisfactory results are obtained by using concrete calculative examples, A new method is provided to carry out finite element stress analysis for different modulus material.
经过实例分析计算，获得了满意的结果。为对这类材料的结构进行有限元应力分析提供了一种新方法。
The finite element stress calculation of the hydraulic rocking shear stand has been described, and the optimization has been carried on in two aspects of force condition and configuration.
介绍液压摆式剪切机机架的有限元应力计算，从受力状态和结构两方面进行优化。
Methods: the finite element model was created by using the standard edentulous jaws model; its stresses and deviation were analyzed with the three-dimensional finite element stress analysis method.
方法：以标准的无牙颌模型为原形建立无牙颌全口义齿的有限元模型，运用三维有限元应力分析。
In a considerable percentage of cases of debt-induced financial stress, credit cards and loans will be a central element.
在相当大比例的债务引发的财务压力案例中，信用卡和贷款是核心因素。
I do think that an element of stress is a good thing, and if used the right way, can actually be a positive thing.
我认为有一点压力是好事，如果处理得当，实际上它是可以带来积极影响的。
However, I do think that an element of stress is a good thing, and if used the right way, can actually be a positive thing.
然而，我认为压力元素确实是一件好事，且如果处理得当，它实际上是可以带来积极影响的事。
In this paper we use boundary element method to separating main stress. It can simplify the problem and provide a practical method for separating main stress.
本文将边界元法引入光弹性应力分析使主应力分离问题得到简化，从而使光弹性应力分析方法更简便可行。
For the plates with finite dimensions, the finite element method is used to obtain the stress distribution and stress concentration around the ovaloid opening.
对于有限尺寸板内开孔的情形，文中用有限单元法来分析腰圆形孔口的应力分布和应力集中。
In calculation, adopted load-unload criterion of stress wave propagation was to decide load-unload state of element and to adjusts and transfers internal stress for tensile failure element as well.
计算中用应力波传播的加卸载判别准则来决定单元的加卸载状态，对受拉破坏单元进行内部应力调整和应力转移。
If the structural element of the stent is symmetrical, the uniform stress appears by force, furthermore, the stress concentration is avoided effectively, and the maximum stress decreases obviously.
支架单元结构的均匀，可使得支架受力时应力分布均匀，且有效避免应力集中现象，其应力最大值明显减小；
We ran finite element analysis stress calculations to determine where the frame needed to be reinforced for maximum strength and stiffness, then reinforced those areas with additional carbon fiber.
我们跑应力有限元分析计算，确定了框架需要得到加强的最大强度和刚度，然后加强这些领域更多的碳纤维。
These are known as the nine components of stress and are illustrated with reference to an infinitesimal rectangular element about a point in figure1.2.
它们被称为应力的九个分量，均示于图1。2中一点附近的无限小的平行六面体单元上。
After a cell is broken, the stress adjustments of the other cells in the system are obtained by finite element method using the broken cell as inner boundary.
当单元破裂后，将破裂单元作为内部边界，利用有限元方法计算由于这个单元破裂对系统其他单元造成的应力调整。
The stress and deformation of crankshaft are calculated by finite element method with six load boundary conditions and three displacement boundary conditions.
分别采用六种载荷边界条件和三种位移边界条件对曲轴应力和变形进行了有限元分析；
This finite element method is employed to analyze the behavior of eccentrically loaded CFST columns, taking initial stress degree, slenderness ratio, and eccentric ratio as the parameters.
应用该方法，以长细比、偏心率和初应力度为主要参数对有初应力的钢管混凝土偏压构件进行了受力性能分析。
This thesis deduces computational formulations of displacement sensitivity and stress sensitivity in structural shape optimization considering geometric nonlinear element.
推导了考虑几何非线性项的结构形状优化位移灵敏度和应力灵敏度计算列式。
The reason for generating the false stress in a transition element connecting a solid element to a thin shell element for stress analysis is considered.
分析了体—壳过渡元中产生“虚假应力”现象的根本原因，给出了两种改进方法。
In this paper the boundary element method based on stress for solving the elastic problems of the plane is proposed.
本文提出了求解平面弹性问题的应力边界元法。
According to the trial, we use finite element analysis program to conduct temperature field and thermal stress analysis of the pier under sunshine, and compared the outcome with experimental results.
根据试验采用有限元分析程序，进行日照作用下桥墩的温度场和温度应力分析，并与实验结果进行对比。
With the welding spot fatigue lifetime pre-estimation method, by combination of the finite element analysis and stress calculation, the welding spot fatigue damage under actual load can be calculated.
采用焊点疲劳寿命预估方法，通过有限元分析并结合应力计算，即可计算出实际载荷工况下的焊点疲劳损伤。
Possibility and efficiency in the application of this method to large finite element analysis are illustrated by an example of the stress analysis for a section of a cable stayed bridge.
以斜拉桥桥段的应力分析为例，说明在大型有限元分析中采用分阶段计算方法的可能性和有效性。
The finite element method was used for analysis of heat stress in chip on board(COB).
本文采用有限元法分析了板上芯片（COB）的热应力分布。
The finite element method was used for analysis of heat stress in chip on board (COB).
本文采用有限元法分析了板上芯片(COB)的热应力分布。
An element means that stress discontinuity from one element to the next are inevitable.
意味着一个单元与近旁单元的应力不连续是不可避免的。
In dealing with the cracking of steel fiber concrete element, the stress release factor and shear transfer coefficient are introduced.
在钢纤维混凝土单元开裂处理中，引入应力释放因子和剪力传递因子。
应用推荐