The forming mechanism of slag skin was studied during electroslag casting.
研究电渣熔铸过程中渣皮的形成机理。
Electroslag furnace is made of slag change electric resistance furnace (esr).
电渣炉是由溶渣实现电热转变的电阻炉(见电渣重熔)。
In this article, the principle of strip electrode electroslag surfacing is introduced.
介绍了带极电渣堆焊的原理。
The detection environment, method and new progress of electroslag casting are introduced.
介绍了电渣熔铸金属液位的检测环境、方法和最新成果。
Electroslag remelt (ESR) furnace is the key equipment for the electroslag remelting process.
电渣重熔炉是电渣重熔过程的典型设备。
The origin of square segregation in high speed tool steel bars in electroslag refining is analyzed.
对电渣重熔高速钢轧材方型偏析形成原因进行了分析试验。
The slag pool and the metallic bath are the most important two regions in Electroslag Casting(ESC).
渣池和金属熔池是电渣熔铸过程中两个最重要的区域。
The products of electroslag remelting steel include 243 designations of alloy steel and superalloy.
产品包括优质合金钢与超级合金243个牌号。
The smelting results show that the new method quite effective realize Intelligent Control of Electroslag furnace.
应用结果表明该方法能够较好地实现电渣炉的智能控制。
The procedure using anneal instead of normalizing will improve the productive efficiency of electroslag welding joint.
用退火代替正火后的电渣焊工艺可大大提高生产效率。
The invention relates to a complex additive for electroslag remelting alloy tool and die steel, and an adding method thereof.
本发明涉及一种电渣重熔合金工模具钢用复合添加剂及其加入方法。
The quality and service performance of large cold roll produced by electroslag remelting (ESR) ingot can be obviously improved.
电渣重熔(esr)钢所生产的冷轧辊能显著改善冷轧辊质量，提高轧辊使用性能。
In this paper, the application of morden control theory to electroslag remelting process controlled by a minicomputer is recommended.
本文介绍现代控制理论在电渣重熔计算机控制中的应用。
It is pointed out that electroslag technology is an ideal process of manufacturing gigantic ingots for 100t up to 300t forging a piece.
指出，电渣技术是生产100t以上直至300 t重大锻件用巨型钢锭的理想方法。
Traditional electroslag remelting technology has the disadvantages of polluting environment and extremely high specific power consumption.
传统的电渣重熔工艺存在着污染环境和比电耗过高的弊病。
Experimental investigation of peculiarities of electroslag remelting of waste titanium chip to produce high-Ti ferro-titanium has been performed.
在有衬电渣炉内，对采用废钛屑为原料生产高品位钛铁合金的工艺进行了试验研究。
In this paper, technical principle on preparation of metal mould by casting method of electroslag smelting and application prospect is described.
本文简述了用电渣熔炼浇铸法制备金属模具的工艺原理和该方法的应用前景。
The cold rolling roller blank was normally made out of electroslag and ingot but was limited in higher production cost and product specification.
冷轧辊辊坯普遍采用电渣钢锭制造，但生产成本高、产品规格受限。
The composition, functions, PLC model selection and program design of PLC plus frequency speed- regulating system on electroslag furnace are briefly introduced.
简要介绍了电渣炉PLC加变频调速控制系统的组成、功能及PLC的选型和程序设计。
The re-bar end used for electroslag welding should be straight, flat and clean free of U-shaped, bruising, concave and convex, bending or distorted deformations.
电渣压力焊焊接使用的钢筋端头应平直、干净，不得有马蹄形、压扁、凸凹不平、弯曲扭曲等严重变形。
Nickel rod needs to be lengthen by argon arc welding before the electroslag refinements, large welding parameters are needed to assure the sufficient penetration.
金属镍在电渣精炼前需用氩弧焊焊接接长，为保证焊接接头具有足够熔深，需要大参数进行焊接。
Within 200mm area of re-bar end surface, it should be free of rust, oil dirt, concrete slurry etc. The contaminated re-bar should be cleaned for electroslag welding.
钢筋端部200mm范围不应有锈蚀、油污、混凝土浆等污染，受污染的钢筋应清理干净后才能进行电渣压力焊焊接。
When producing the rare earths Fe-Cr-Al alloy by electroslag remelting method, the optimum quantity of rare earths added to three phase lining electroslag furnace is 0.5%.
电渣双联法生产稀土铁铬铝合金时，稀土在三相有衬电渣炉中的最佳加入量为0.5%。
The flow of the molten slag pool determines the temperature distribution and the pool profiles in the electroslag casting process, which affects the quality of ingot casting.
电渣熔铸过程中熔渣的流动决定了熔铸体系温度场的分布以及金属熔池的形状，最终影响熔铸钢锭的质量。
The deepness of slag pool is one of the most important technics parameters in the electroslag casting process, which affects stabilization of the process and product's quality.
渣池深度是电渣熔铸过程中重要的工艺参数之一，它直接影响到熔铸过程的稳定和产品质量。
According to the specification of equipment, the hardware and PLC application software have been designed. This control system has been used in double wires electroslag welding.
根据设备的技术要求设计了系统硬件和PLC应用软件，该系统已用于自制双丝电渣焊设备。
The features and problems of manufacturing high nitrogen steels by the electroslag remelting method at normal atmospheric pressure and high pressure have been discussed in detail.
概述了目前高氮钢的主要制备方法，重点讨论了常压和高压电渣重熔高氮钢的特点和存在的问题；
The technological parameters determine the metal pool profile and the microstructure's size and tropism in the electroslag casting process, which affects the quality of ingot casting.
电渣熔铸中的工艺参数决定金属熔池的形状和微观晶粒的尺寸及取向，并最终影响熔铸钢锭的质量。
Electroslag remelting's consumable electrode current is determined by the distance between electrode and slag bath which is determined by the rotate speed of motors driven by electrode.
电渣重熔的自耗电极电流大小取决于电极与渣池的距离，而该距离大小又取决于电极驱动电机的转速。
Electroslag remelting's consumable electrode current is determined by the distance between electrode and slag bath which is determined by the rotate speed of motors driven by electrode.
电渣重熔的自耗电极电流大小取决于电极与渣池的距离，而该距离大小又取决于电极驱动电机的转速。
应用推荐