I've smashed the electrometer.
我把静电计摔碎了。
With an electrometer, the input offset current is very low.
静电计的输入偏置电流是很低的。
Main control Unit, two-channel electrometer and servo controller.
主控制器单元，带有两通道静电计和伺服控制器。
Figure 2-33 shows the electrometer ohmmeter measuring a resistance (R).
图2-33示出静电计欧姆计测量电阻（R）的情况。
Connect an electrometer to the switch card output and measure the cur rent.
将一个静电计连接到开关卡输出并测量电流。
Use an adapter to connect the BNC connector to the triax input of the electrometer.
用一个适配器把BNC连接器连到静电计的三同轴输入端。
Therefore, a voltmeter with high input resistance, such as an electrometer, is required.
所以需要使用具有高输入电阻的电压表，例如静电计。
Figure 1-18 shows the basic configuration of an alternative form of electrometer ohmmeter.
图1 -18示出另一种形式的静电计欧姆计的基本电路结构。
VC type electrometer is an electrostatic instrument of alternating current induction type.
VC型静电仪是一种交流感应式静电仪表。
The circuit of the electrometer when used as a voltmeter is actually as shown in Figure 2-6.
当静电计作为电压表使用时，其电路实际上如图2 - 6所示。
A picoammeter is an ammeter built along the lines of the ammeter function of an electrometer.
皮安表是安培表的一个门类，其实质上是静电计中安培表功能的延续。
The damping circuit may already be built into the electrometer or may be an external circuit.
衰减电路可以装在静电计的内部，也可以是一个外部电路。
Figure 2-42 illustrates a clipped waveform taken from the 2v analog output of an electrometer.
图2 - 42示出在静电计的2V模拟输出端观察到的限幅波形。
The ohmmeter USES an internal current source and electrometer voltmeter to make the measurement.
欧姆计使用内部的电流源和静电计电压表来进行测量。
Usually, this method requires two instruments: a voltage source and a picoammeter or electrometer.
通常，这种方法需要使用两台仪器：一台电压源和一台皮安计或静电计。
When using the electrometer ohmmeter, measurement accuracy can be affected by a variety of factors.
使用静电计欧姆计时，测量准确度会受到各种因素的影响。
Figure 4-2 illustrates the basic circuit that USES an electrometer to determine dielectric absorption.
图4 - 2说明使用静电计确定介电吸收的基本电路。
More information on the measurement procedure can be found in the instruction manual of the electrometer.
有关测量方法的更详细的信息可以在静电计的操作手册中找到。
To measure the offset of a switch card, connect the output of the card to a pico ammeter or electrometer.
若要测量开关卡的偏移电流，请将卡的输出连接到一台皮安计或静电计。
Using with a vibrating capacitor electrometer and a digital voltmeter, the stability is better than 0.1%.
它配合动电容静电计和数字电压表进行测量，其稳定性好于0.1%。
The external feedback mode allows an external device to be used as the feedback element of the electrometer.
外部反馈模式允许使用外部器件来作静电计的反馈元件。
When a charged object is placed within the inside electrode, an induced charge will flow into the electrometer.
当带电物体放到内电极里面的时候，就有感生电荷流过静电计。
The resistors (RL) are current limiting resistors used to protect the switches and electrometer from high current.
电阻器（RL）是电流限制电阻器，用来保护开关和静电计不受大电流的损害。
An electrometer makes an ideal coulombmeter because it has very low input offset current and high input resistance.
静电计是一个理想的库仑计，因为它具有非常低的输入偏置电流和很高的输入电阻。
The measured current is usually quite small, so a picoammeter or electrometer is often required to make the measurement.
测得的电流通常非常小，因此往往需要使用皮安计或静电计进行测量。
Figure 2-39 shows an electrometer connected to a current source that consists of a voltage source in series with a resistor.
图2 - 39所示为静电计和由电压源及电阻器串联组成的电流源相连接。
High resistance insulation in the test circuits is one of the first requirements of making successful electrometer measurements.
在测试电路中，高绝缘电阻是成功地进行静电计测量的首要要求之一。
Figure 2-24 shows a protection circuit for an electrometer ammeter or picoammeter, consisting of a resistor and two diodes (1n3595).
图2 - 24示出静电计或皮安计的过载保护电路，其中包括一个电阻器和两个二极管(1n3595)。
Connect the shield of the test fixture to the LO of the electrometer and connect the LO of the electrometer to the LO of the source.
将测试夹具的屏蔽端连到静电计的LO端，再将静电计的LO 端连到源的LO端。
General Electrometer Considerations: a discussion of techniques and error sources that affect high impedance measurements in general.
一般静电计要考虑的问题：一般性地讨论影响高阻测量的技术和误差来源。
应用推荐