The panel tester is arranged in the frontal border area, and electrically connected with the electrode wire.
面板测试装置配置于额缘区中，且面板测试装置电性连接电极配线。
Take care of wire cut electrode wire transfer for one-way transmission, disposable, so nonexistent wire electrode thinner.
慢走丝线切割的电极丝传送为单向输送，一次性使用，所以不存在电极丝变细的情况。
The method uses a data line to connect common electrode wire signals and utilizes the existing auxiliary line to connect data line signals.
利用该辅助线接续该第一资料线，使传送到该第一资料线的影像信号经由该辅助线提供；
With the principle of measuring resistance, the paper carries through the theory analysis about possibility of measurement method with short electrode wire.
从接地电阻的测量原理出发，讨论了采用短电流极引线测量地网接地电阻的可行性。
Due to sectional use of the electrode wire, the loss of the electrode wire is small under the condition of fine cutting, so that the cutting precision can be improved.
本发明通过分段使用电极丝，在精切时，电极丝的损耗极小，可提高切割精度。
With a view to the deficiency of grounding resistance measurement at present, a new method with short current-electrode wire based on computer auxiliary analysis is presented.
针对目前的接地电阻测量方法的缺点，提出了以计算机辅助分析为基础的短电流极引线测量方法，并对电流引线长度的选取作了分析。
Through the test electrode wire cut to optimize pulse power parameter and machine parameters, eventually completed the large Angle, under the abnormity bores take care of wire cut.
通过试切来优化电极丝脉冲电源参数及机床参数，最终解决了大角度上、下异形孔的慢走丝线切割。
Through ANSYS simulation of vibration for the electrode wire. Proposed the measure of reduce vibration of electrode wire in order to improve the electrode wire cutting machine quality.
通过对电极丝振动的ANSYS模拟，提出了降低电极丝振动以此来提高线切割机床加工质量的方法。
The panel tester comprises a short circuit rod and a plurality of switch elements, wherein the switch elements are electrically connected with the short circuit rod and the electrode wire.
面板测试装置包括一短路杆以及多个开关元件，其中开关元件电性连接短路杆与电极配线。
They flow across the wire to the second electrode, which acts as an electron sink.
它们沿着线到达充当一个电子穴的第二电极。
This forces the freed electrons to travel to the second electrode through a wire, creating an electric current.
而自由电子则通过一条导线移动至第二电极，从而产生电流。
Use an alligator-clip wire to connect the copper electrode of potato A to the plus (+) connection in the clock.
用一个鳄鱼嘴导线连接土豆A的铜电极至钟的正（+）极
With austenitic welding material, solid wire, flux-cored wire and electrode, welded joint mechanical property of TCS ferritic stainless steel all can meet usability.
T CS铁素体不锈钢采用奥氏体型焊材，实芯焊丝、药芯焊丝和电焊条方法，焊接接头力学性能可以满足使用要求。
Since the electrode material of compensating wire and cable and thermocouple are different, the two contacts at the connection must be at the same temperature to avoid further error.
由于补偿导线和热电偶的热电级材料并不完全相同，所以要求它们连接处两接点温度相同，否则又会引入误差。
Electrocatalysis of carbon atom wire (CAW) modified electrode to the electrochemical reaction of uric acid was investigated by using cyclic voltammetry and differential pulse voltammetry.
通过循环伏安法和差分脉冲伏安法研究了碳原子线(CAW)修饰电极对尿酸电化学反应的催化作用。
The wire beam electrode method could be developed to study the fast electrodepositing behavior of metal.
探讨了不同材质的丝束电极和不同镀液对金属镍的快速电沉积行为的影响。
A new type of amitriptyline coated wire electrode (CWE) with bilayer polymeric films is reported.
本文报告一种性能良好的新型双层聚合膜阿米替林涂丝电极的研制。
Both the theory and the practice show that the parallel electrode source is more practical, while the explosion wire source has a higher efficiency.
理论和实践都表明，平行电极放电震源比较实用，而爆炸丝放电震源效率较高。
In this paper, some new points were put forward based on theoretical analysis of the discharge gap of Electric discharge Generating machining based on wire electrode.
针对基于线电极展成加工的放电间隙进行了理论分析，提出了一些新的研究观点。
The polypropylene film as the dielectric and aluminum foil as the electrode, series structure, epoxy resin coated and radial CP wire.
采用聚丙烯膜作介质，铝箔作电极卷绕而成的串联结构型式，环氧树脂包封，单向引出。
Potential variation of rust preventing oil film after its degradation was studied by using wire beam electrode.
采用丝束电极研究防锈油膜失效之前的电位变化。
Weld penetration and wire melting speed of AC PMIG welding not only have relationship with welding current but also with electrode negative ratio.
交流脉冲MIG焊其焊缝熔深及焊丝熔化速度不仅与焊接电流有关，而且与负极性比率有关。
The electrode concerned in this article is a medical one - a platinum wire electrode made by covering glycyrrhetinic acid with double - decked polymer film.
本文研制的电极是在铂丝上涂双层聚合膜而制成的一种甘草次酸涂丝药物电极。
Indistinct pattern are sometimes found on the wire electrode wound regularly in reciprocating travelling WEDM.
高速走丝电火花线切割加工过程中，电极丝有时会出现先有花斑后断丝的现象。
Wire Electrical Discharge Machining Milling (wire EDM-Milling) is a novel kind of EDM-Milling method that has the distinct advantage of electrode compensation via the wire electrode slow traveling.
线电极放电铣削加工是一种新型电火花铣削技术，它的最大优点是可通过线电极的缓慢移动来补偿加工中的电极损耗。
The electrochemical inhomogeneity on oil painted metal was studied by wire beam electrode.
采用丝束电极，对涂油金属的电化学不均匀性进行了研究。
The electrochemical inhomogeneity on oil painted metal was studied by wire beam electrode.
采用丝束电极，对涂油金属的电化学不均匀性进行了研究。
应用推荐