This welding process joints work pieces by melting the electrode and the base metal with the heat from the electric arc between the electrode and the work piece.
它是一种利用焊条与工件之间电弧产生的热量熔化焊条和母材而将被焊工件连接起来的焊接方法。
The effect of process parameters on the electric insulance of micro arc oxidated ceramic coat on aluminium plate is studied.
研究了工艺参数对铝微弧氧化陶瓷层电绝缘性能的影响规律。
The microhardness of JCW-S-AM coatings prepared by high velocity electric arc spraying on conditions of different process parameters was tested by hardometer.
采用超音速电弧喷涂设备在不同工艺参数条件下制备JCW - S - AM涂层，利用显微硬度计测定各种涂层的显微硬度。
Principles of pyrogenic process, wet process and other methods are more fully described. The feasibility of the technology of comprehensively treating electric arc furnace dust is discussed.
详细陈述了火法、湿法以及其它方法处理电弧炉炉尘的原理，并且简述了这些工艺的可行性。
Passive visual sensing method is the major method for sensing welding process, the principle of which is to capture weld pool image by the illumination of electric arc.
被动式视觉传感方法是焊接过程传感的一种主要方法，其主要原理是利用电弧光照射熔池表面获得熔池图像。
This paper introduces the technological process, equipment characteristics and the benefit of vaporized cooling project of Consteel electric arc furnace.
介绍了康斯迪电弧炉汽化冷却项目的工艺流程、设备特点、经济效益。
Welding process factors consist of welding electric current, electric arc voltage, welding speed, etc.
焊接工艺因素包括焊接电流、电弧电压、焊接速度等。
Modeling of dynamic electric arc and analyzing on the electric arc dynamic characteristics during the interrupting process.
动态电弧模型的建立以及开断过程电弧动态特性的研究。
The top-bottom combined blown process for the electric arc furnace has advantages of low cost, ease of operation and satisfactory agitation results.
电弧炉顶底复吹技术，具有成本低，操作方便，搅拌效果好等优点。
Its electric characteristic, structure feature, fault analysis, interface circuit and arc welding process program are analyzed and discussed.
对其电气性能、结构特点，故障诊断、接口电路及弧焊工作程序等作了比较全面的分析和讨论。
On the producing process of the miniature metal halide lamp, due to its bulk, the measurement of its dimensions especially the inside diameter of the necks of the electric arc tube is very difficult.
在超小功率金卤灯生产中，由于受其体积限制，各种尺寸尤其是电弧管泡壳两侧缩颈处的内径测量一直是比较困难的。
The electric arc furnace (EAF) dust pellets were reduced in isothermal condition in order to make the reduction similar to the EAF production, and the kinetics of the reduction process is researched.
为使还原条件与实际电弧炉生产相接近，在等温条件下对电弧炉粉尘球团的还原过程动力学进行了研究。
The electric arc steelmaking process may be divided into the following four stages: charging, melting, refining and tapping.
电弧炉炼钢可以分为以下4个阶段：装料，熔化，精炼和出钢。
The electric arc steelmaking process may be divided into the following four stages: charging, melting, refining and tapping.
电弧炉炼钢可以分为以下4个阶段：装料，熔化，精炼和出钢。
应用推荐