To illustrate the foregoing analysis, consider a linear elastic solid.
为了举例阐明以上的分析，我们考虑一种线性的弹性固体。
The strain, geometric equation and principal strain of the elastic solid are all-sidedly studied by using the method of dyad analysis.
利用并失分析法，对弹性体的应变、几何方程和主应变进行了全面研究。
This paper describes the removal process of odious gas H 2S with the biological membrane method, which adopts PVC elastic solid filler.
采用PVC弹性立体填料进行了好氧生物法脱硫的研究。
An infinite elastic solid containing a doubly periodic rectangular array of cylindrical inclusions under longitudinal shear is dealt with.
研究无限介质中矩形排列双周期圆柱形夹杂的纵向剪切问题。
The mechanical model of composite energy storage flywheel is built based on the orthotropic elastic solid basic theory and the finite element theory.
分别基于平面应力型全弹性模型和三维数值模型建立了计算复合材料飞轮破坏转速的二维和三维算法。
The polarization property of material point of solid phase has some similarities with the polarization of Rayleigh Wave in free surface of uniform elastic solid;
固相质点的偏振特性与均匀弹性固体自由界面上的瑞利波的偏振有某些类似之处；
This article USES a finite difference time domain method to study the two-dimensional sound field characteristics of elastic solids based on elastic solid equations.
对弹性固体中的声场方程应用时域有限差分法，进行了二维声场特性研究。
The effect of blank holder thickness on stress transfer was studied by means of an elastic solid element finite element model. The simulation results were verified by experiments.
利用弹性实体单元有限元模型研究了压边圈厚度对压边应力传递的影响规律，并与实验结果进行了对比分析。
This paper deals with the plane strain problem of non-straight boundary semi infinite elastic solid to which a concentrated force is applied at the midpoint of the bottom of a groove.
本文对几种不同形状之刻槽的折线界面的半无限弹性体，在其槽底施以集中力的平面应变问题做了讨论。
We get the conclusion that the expansive pressure is determined by elastic modulus of the expanded solid medium.
得出膨胀力取决于限制膨胀的固体介质的弹性模量的结论。
As a new structure of solid matter quasicrystal brings profound new ideas to the traditional condensed matter physics, its elastic equations are more complicated than that of traditional crystal.
准晶作为一种新的固态物质结构给传统的凝聚态物理学带来了深刻的变革，其弹性基本方程比传统晶体的弹性基本方程要复杂得多。
A high solid elastic polyurethane prepolymer has been prepared based on MDI, PAPI, HDI, IPDI and polyester polyols and polyether polyols.
采用MDI、PAPI、HDI、IPDI等不同的异氰酸酯和聚酯多元醇、聚醚多元醇等反应，制备高固体分的聚氨酯弹性体预聚物。
The theoretical basis of pulse hammer excitation method used to detect the damage and measure the dynamic elastic modulus of solid wood flooring is briefly explained.
介绍了脉冲锤击法检测实木地板损伤及测定其动态弹性模量的理论依据，并通过有限元模拟与试验验证了其可行性。
A formula of high elastic middle compound for solid tire has been developed.
对实心轮胎高弹性中间胶的配方进行了研究。
The main products are usually used to nap the high solid content, high viscosity elastic coating.
通常用来拉毛的产品主要是高固含量、高粘度的弹性涂料。
Rigid casings will make the antenna more solid and rubber ones will allow it to stretch like an elastic band.
刚性的外壳会使这种天线更坚固，橡胶外皮可以让它像橡皮筋一样伸展。
A spherical cavitated bifurcation problem is examined for a solid sphere composed of a class of compressible hyper-elastic materials.
研究了一类可压缩超弹性材料组成的球体的空穴分岔问题。
The propagation process of ultrasonic pulse along solid-solid interface is recorded by the dynamic photo-elastic method in this paper.
本文报导了用动态光弹法记录的沿两种玻璃形成的界面上超声脉冲的传播过程。
In numerical analysis, the stress distribution and the effects of the parameters in elastic stage are obtained by the finite element program of 20-node 3-dimensional solid element.
电算采用三维实体单元，对弹性状态下这种柱的受力特点和变参数影响进行了分析。
Numerical results of the ultrasonic propagation characteristics in a liquid-solid coupled interface are in accord with those obtained by photo-elastic experiments.
分析了液固耦合情况下的超声波传播特性，取得了与光弹法物理试验相一致的结果。
Influences of the elastic module ratio and the volume fraction of solid phases on optimal design are investigated.
采用分层优化方法并结合算例研究了实体材料模量相对比值、材料组分变化对优化结果的影响。
In Chapter 5, problem of radial motion for a solid sphere composed of an imperfect incompressible hyper-elastic material, subjected to a surface tensile dead load, is examined.
第五章中，研究了具有缺陷的不可压超弹性材料组成的球体在表面均布的拉伸死载荷作用下的径向运动问题。
Heat-fluid-solid coupling and contact thermo-elastic-plastic analysis was carried for a certain turbine blade-disc, and the stress and strain-time course was obtained in this paper.
采用随机有限元方法， 针对某燃气涡轮盘-片进行了热流固耦合及接触热弹塑性分析，得到了随机应力应变响应；
Heat-fluid-solid coupling and contact thermo-elastic-plastic analysis was carried for a certain turbine blade-disc, and the stress and strain-time course was obtained in this paper.
采用随机有限元方法， 针对某燃气涡轮盘-片进行了热流固耦合及接触热弹塑性分析，得到了随机应力应变响应；
应用推荐