In this paper, microcontroller, stepper motor driver chips, character LCD and keypad array, build a set of stepper motor controller and driver as one of the stepping motor control system.
本文应用单片机、步进电机驱动芯片、字符型LCD和键盘阵列，构建了集步进电机控制器和驱动器为一体的步进电机控制系统。
The experiment results show that the new control system can avoid the start shock and better respond to the starting intent of driver and road conditions.
试验结果表明，新的控制系统避免了起步冲击和不能很好适应驾驶员起步意图与路况的问题。
The dissertation consists of hardware design, driver development, CAN bus control system composing.
本论文包括硬件设计、驱动程序开发和组成CAN总线控制系统三部分。
And the paper studies and works out monitoring software in the whole system, including A/D acquisition and control, data exchange, DCI driver and digital signal filtering and data preprocess software.
并研究编制了整个系统的监控软件，包括A/D采集和控制、数据通讯、显控等部分接口驱动程序以及数字信号滤波数据预处理软件；
Through the experiments of many drivers, parameters of driver model with different levels are identified, which will be helpful in improving design of the intelligent vehicle control system.
通过大量的实际驾驶人员的试验数据，辨识出各种水平的驾驶员模型参数，为改进智能车控制系统的设计提供了依据。
Hardware circuit part of control system mainly includes controller, sensor, and motor driver chip.
控制系统的硬件电路部分主要包括控制器、传感器和电机驱动芯片。
This system consists of steering electronic control unit (ECU), all hydraulic steering, stepping motor, stepping motor driver and angular displacement sensor, etc.
该系统由转向电子控制单元(ecu)、全液压转向器、步进电机、步进电机驱动器、角位移传感器等组成。
The paper analyzes the principle of components of magneto optical disk driver focusing and tracking servo system, then designs and realizes a DSP based digital servo control system.
分析了磁光盘驱动器聚焦与循轨数字伺服系统各组成部分的原理，并设计和实现了一套基于DSP的数字伺服控制系统。
The working principle of a new double closed-loop thyristor trigger CF6B-2A and its application in the control system of driver motor in the extruder were introduced.
介绍了双闭环可控硅触发器CF 6 B - 2a的工作原理，并将该器件应用于挤塑机主驱动电动机控制系统中。
The fuzzy on-line control system of close-loop is made up when the power driver board is added in primary on-line checking system.
在原来在线检测的硬件系统中加入功率驱动板，就构成了闭环模糊在线控制系统。
An experimental device was designed and established to detect seam automatically employing vision sensor, stepper motor driver and the industrial PC control system.
本课题通过一套焊缝跟踪实验装置，采用视觉传感、步进驱动和工控机控制系统，来实现焊缝的自动识别控制。
The conveyer belt adopts the CST step driver control, and the realization of the soft-startup and power balance depends on the proportional valve and control system.
带式输送机采用CST多级驱动控制，通过比例阀及控制系统实现软起动与功率平衡。
Secondly, servo control tache is introduced briefly, and how to realize a closed-loop position control system which USES stepping motor as driver component is presented.
其次，对于伺服控制环节，实现了以步进电机为驱动元件的闭环位置控制系统。
This paper is based on developing the high-speed intelligent card, main control card of MSCIS interface system and device driver of the communication card.
论文是在研制MSCIS接口系统的高速智能通信卡、主控制卡和开发通信卡设备驱动程序的基础上完成的。
Motion control system is composed of the motor, driver, controller and sensor.
运动控制系统包括电机、驱动器、控制器和传感器。
The driver system has some merits such as stability, high precision for motion control, also, the system has intelligent characteristic?
该驱动系统有着稳定可靠，运动控制精度高和具有智能化等优点。
DC power supply is mainly provide constant voltage power supply for control circuit, driver circuit and a variety of protection circuits and allows the system to work properly.
直流稳压电源主要是用于对系统中的控制电路、驱动电路以及各种保护电路提供恒压电源，使得系统能够正常工作。
The control system are consisted of computer, laser sensor, A/D converter and the power driver of output etc.
实验系统由计算机、激光传感器、A／D转换器及输出功率驱动器等实验装置组成；
The control interface board communicated to computer with USB interface. We designed WDM driver on USB bus which made the computer control the whole system through the USB interface.
控制接口板采用USB接口与主机通信，我们设计了USB总线的WDM驱动程序使主机通过USB控制接口板控制整个系统。
The system hardware includes main control board, display and button board, and motor driver board.
系统的硬件电路板主要包括主控制板、显示按键板、电机驱动板。
The control system hardware platform is composed of motor, driver, motion control card and computer.
控制系统硬件平台由电机、驱动器、运动控制卡和主机构成。
The system bandwidth of conventional voltage-control-mode motor driver circuits is limited by the intrinsic frequency of the load, and its phase lag is also load-dependent.
传统电压控制模式的电机驱动电路系统频率都受电机的本征频率制约，其相位延迟会随负载的变化而变化。
Design and develop embedded software for household appliance inverter driver system and control system in close cooperation with customers.
与客户紧密合作，设计开发家电变频驱动系统和控制系统的嵌入式软件。
This paper presents the application of a full-digital AC-servo driver to an automatic cutting control system for aluminium plastic tubes.
本文主要介绍了全数字式交流伺服驱动器在铝塑管自动切割控制系统中的应用。
Point to point control is adopted because a stepping motor is used as a driver. A grating displacement detector is applied in the feedback loop, forming a close loop control system.
该系统以步进电机作为驱动器件，以光栅位移检测装置作为位移检测反馈器件，采用点位控制原理，形成一个闭环似移控制系统。
The system software driver allows a single function call to set up and control multiple E4360s in a system.
系统软件驱动允许在系统中启动单个功能并控制E4360。
The system composition and working principle of hydro-viscous driver (HVD) control system are presented briefly in this paper.
本文简要介绍了液体粘性调速离合器控制系统组成及其工作原理。
The design scheme of synchronous control system on production's process of color plate is introduced. The design principles of synchronous control system on main driver is provided.
介绍了彩钢板自动生产线的主驱动变频同步控制系统方案，阐述了主驱动变频同步控制系统的设计原理。
Meanwhile long-distance reading and setting of the pump-module LD driver can be achieved by the design of serial device circuit control system.
具有串口通信电流源控制系统，能够实现对驱动电流值的远程读取与设置。
The saving energy control system is proposed for problem of oil drawing machine electric driver which efficiency and power factor is low.
针对抽油机电驱动装置效率和功率因数低、耗能严重的问题，研制了一台新型的抽油机节能控制系统。
应用推荐