Is SPC used in Drilling process?
钻孔制程是否使用SPC ？
The dual tube drilling process and the anchor drill is detailed.
详细介绍了“双管钻进”方法和钻机情况。
In deep drilling process, casing wear is the problem that cannot be ignored.
在深井、超深井钻井过程中，套管磨损有可能导致套管封隔失效和油气井的早期报废。
The drilling process and techniques taken are described in detail in this paper.
详细介绍了施工过程及技术措施。
This paper describes and summarizes the core drilling process and the technical measures.
文章介绍并总结了该项目岩芯钻探钻孔施工工艺与技术措施。
Mud in the drilling process, the drilling mud or water transport machinery such as washing fluid.
泥浆泵是在钻探过程中，向钻孔输送泥浆或水等冲洗液的机械。
Mud din the drilling process, the drilling mud or water transport machinery such as washing fluid.
鉃泥浆泵是在钻井过程中，向钻井输送泥浆或水等介质的机械。
The measurement of the inclination angle and the azimuth angle of a well in the drilling process is important.
钻探过程中钻井的倾斜角和方位角的测量至关重要。
Proper drilling process can be adopted in crossing of many types of formations, which has wider scope of application.
采用合适的钻进工艺，可以穿越许多类型的地层，有较宽的适用范围。
Based on the analysis of woodworking drilling process, the design plan of a horizontal drilling machine is determined.
通过对木材钻孔工艺的分析，确定卧式木工钻孔机的设计方案。
State monitoring and fault diagnosis of drilling process is the significant support for safe working of drilling system.
钻井过程状态监测与故障诊断是钻井系统安全运行过程中的重要保障。
The wash pipe packing of drilling swivel showed wear-and-tear continually in drilling process due to its structural design.
钻井（水）龙头由于结构设计的原因，冲管盘根在钻井过程中不断磨损，特别是在高压泥浆的作用下，盘根密封常常被破坏。
Antiquated term for a deviated wellbore, usually used to describe a well deviated accidentally during the drilling process.
描述斜井的一个陈旧术语，通常是指在钻井过程中由于事故原因而使之倾斜的井眼。
The drilling wire rope of a rig's hoisting system suddenly broke during drilling process, cause serious damage of equipment.
钻机提升系统的钻井钢丝绳在油田钻井过程中突然断裂，造成设备顿钻事故。
The article describes how DF concept is used in the design of pressure feeders in small-diameter deep-hole drilling process.
介绍如何应用DF 系统原理设计小直径深孔加工中吸压送水器的问题。
During drilling process, screw drill motor sometimes doesn't work properly or even seriously damaged because of sand jamming.
在钻井施工作业中，螺杆钻具常因砂卡导致螺杆马达工作失效，导致螺杆钻具报废，严重影响了正常钻井作业。
Drilling instrument is the major application to monitor and analyze the drilling process, making drilling more safe and rational.
钻井参数仪表是钻井工程监测钻井过程、进行科学分析和科学决策的重要工具。
A miniaturized information monitoring system for drilling process is developed in the light of the particularity of oil drilling.
针对钻井生产过程的特殊性，开发了钻井过程一种小型化信息监测系统。
The rock stratum drilled by a rotary drill is random distributed and complicated, so it is difficult to define the drilling process.
牙轮钻机钻凿的岩层是随机分布、错综复杂的，因而钻进过程难以定义。
Abstract : the drilling wire rope of a rig ' s hoisting system suddenly brokeduring drilling process , cause serious damage of equipment.
文摘：钻机提升系统的钻井钢丝绳在油田钻井过程中突然断裂，造成设备顿钻事故。
This article briefly introduces the drill bit condition effected during drilling process and the program - Ming technique to drilling data.
简要介绍数控钻孔加工过程中，钻头的受力情况和对应钻孔程序的编制技巧。
The measurement of engineering parameters near the bit while drilling is of significant importance for the safety and efficiency in a drilling process.
钻井过程中，近钻头处钻压、扭矩等钻井工程参数的随钻准确测量对安全、高效钻井是十分重要的。
This paper describes the theory, features and testing results of the air reverse circulation drilling process used in geo physical blast hole drilling.
概述了空气反循环钻进工艺应用于物探爆破孔施工的原理、特点及其试验应用情况。
This article introduces the polishing and drilling process of faceted quartz crystal. The characters of equipments and polishing materials are also discussed.
主要介绍刻面水晶的抛光工艺和钻孔工艺，并对加工设备和各种抛光材料的性能、特点作了分析。
The first drilling hole of the Wenchuan earthquake fault science drilling project (WFSD-1) experienced up to more than 30 meters of the fault gouge drilling process.
汶川地震断裂带科学钻探项目一号孔(WFSD - 1)钻遇了30多米的断层泥。
Drilling parameters instrument is the important implement to monitor and analyze the drilling process, and to make scientific decision - making about drilling process.
钻井参数仪表是钻井工程中监测钻井过程、进行科学分析和科学决策的重要工具。
In this paper, a monitoring system of drilling process by using a McS-51 single chip computer is described, and the working principle, hardware and software are given.
本文介绍了一种用MCS—51单片机实现的钻削过程故障监测系统，给出了系统的工作原理、硬件结构及软件设计思想。
In this paper, a monitoring system of drilling process by using a McS-51 single chip computer is described, and the working principle, hardware and software are given.
本文介绍了一种用MCS—51单片机实现的钻削过程故障监测系统，给出了系统的工作原理、硬件结构及软件设计思想。
应用推荐