Position accuracy: as per drawing requirements.
位置精度：符合图纸要求。
The location of the diesel engine shall be marked according to the drawing requirements.
根据图纸要求，划出柴油机定位坐标。
The drawing requirements were met by NC interpolation and application needs were satisfied.
通过数控插补方法加工出来的高精度球轴承符合图纸要求，满足了使用需要。
Carry out incoming inspection based on inspection standard of raw material, control plan and drawing requirements, eliminate unqualified raw materials from the very beginning.
根据原材料检验标准、控制计划及图纸的要求对原材料进行检验，杜绝不合格品的投入生产。
Plastic coated gabion cages retaining wall of basement and its compactness, base area buried depth and the line length and width in appearance, should be fitting for drawing requirements.
包塑石笼网箱挡土墙的基底及其密实度，底子网箱入土深度和外貌线长度及宽度，均应相宜描画需求。
Drawing these classifiers incorrectly will likely confuse readers of your structure diagram, and the ensuing system will probably not meet requirements.
不正确地绘制这些分类器，很有可能将使你的结构图读者感到混乱，以后的系统将不能适应需求。
In my previous article, I discussed the requirements for one such lightweight solution, drawing from my experience with e-commerce XML projects.
在上一篇文章中，我根据自己从事e - commerce XML项目的经验，讨论了这种轻量级解决方案的需求。
It is drawing up requirements that equipment, from tankers to service platforms and drilling RIGS, should be mainly locally produced.
这会提升各种设备的需求量，包括油轮到检修平台和钻井塔，应该以本地生产为主。
Then, design institute edits technology specification of main auxiliary equipment, drawing for site test pile and requirements for test pile.
之后设计院编写主要辅机设备的技术规范书及现场试桩所需的试验桩图纸及试桩要求。
The nameplates, drawing frame, bulletin boards, warning plates, the identification of each room and cabin shall be written in English according to requirements of the Owner and the authorities.
铭牌、图框、公告栏、警告牌、识别各类房间和舱室的铭牌应该按照船东要求以及主管当局要求用英语书写。
Generally, the patent lawyer will direct the preparation of the drawings by a patent draftsman familiar with the drawing formality requirements of the U. S. patent Office.
一般来讲，专利律师将指导由熟悉美国专利局绘图程序要求的专利绘图员绘制图样。
Drawing used to make final decision with basic mould messages such as structure, operation, main dimension, special requirements and so on.
具备模具结构、运作、主要尺寸、特别要求等，定案会议用图纸。
Drawing through the products manufactured will be able to understand the design requirements.
通过制品的零件图就可以了解制品的设计要求。
On the basis of this, process planning of 8 ducts of 4 specifications are designed and machined. The products fully meet the requirements of the drawing.
在此基础上，对4种规格8件风道零件进行了工艺过程设计和实际加工，产品完全符合图纸要求。
Follows up realization, compliance with requirements and drawing and controls quality of the construction and modification work.
跟进施工及改造工作的实现、符合要求、绘图和质量控制。
It describes the process by the steps of defining evaluation requirements, prescribing, designing and doing evaluation, thus, drawing evaluation conclusion, and in addition, gives an example.
通过确立评价需求、规定评价、设计评价、执行评价、做出评价结论等步骤详细描述了该方法，并给出软件的评价实例。
The drawing must be a true and complete statement of the designer's requirements expressed in such a way that the part is convenient to manufacture.
图纸必须按方便制造零件的方式将设计者的要求真实和完整地表达出来。
The re-bar binding should be executed according to the requirements of the drawing. All specification, dimension, quantity and spacing should be checked correct.
钢筋绑扎将按图纸要求进行，所有规格、尺寸、数量、间距必须核对准确。
Based on the analysis of the data status and the data requirements, the geological and mineral information has been classified into four types, table, document, drawing and catalog directory.
通过资料现状与数据需求分析，将地质矿产资料划分为表格、文档、图件和目录簿四类。
The system has met the requirements of slab casting, improved continuous drawing speed and reduced the cost.
该系统满足了板坯铸钢要求，提高了连检率，降低了生产成本。
It puts forward the "satisfying cognitive demands" navigation map drawing scheme adapting to the LBS condition based on both the space cognitive theory and the terminal hardware and user requirements.
基于空间认知理论和移动环境下的硬件与用户需求，提出适应lbs使用环境的“以满足空间认知需求”的导航地图制作方案。
Otherwise, raw material in trial run shall conform the requirements in component drawing.
另外，试模材料必须按元件图纸的要求进行。
During information extracting, the algorithm can restore the original engineering drawing accurately, and meets the requirements of high-precision machining, and also realizes the blind extraction.
提取时可以精确地恢复原始工程图，满足了工程图加工精度高的要求，并且实现了盲提取。
Prior to installation, check first whether location of installation node, installation dimension and damper model etc meet the requirements of design drawing and documents.
安装前首先应核对安装节点的位置、安装尺寸、阻尼器的型号等是否符合设计图纸及文件的要求。
Because of drawing reproduction and possible confusion and for clarity, Figure 1 – SAE J577 Vibration Test Machine drawing has been removed. Only the vibration requirements are shown.
由于复印图纸可能不够清楚而引起混淆同时为了确保清晰，图1-SAEJ577震动测试仪图纸被移除。只显示震动测试要求。
Other requirements include drawing up of the ec declaration of conformity, carrying out of safety assessments under Article 18, and production control on manufacturing process.
其它要求还有EC合格声明，根据第18条进行安全评估，以及制造流程的生产控制等。
Other requirements include drawing up of the ec declaration of conformity, carrying out of safety assessments under Article 18, and production control on manufacturing process.
其它要求还有EC合格声明，根据第18条进行安全评估，以及制造流程的生产控制等。
应用推荐