In dimensioning a drawing, the Numbers placed in the dimension lines represent dimension that are only approximate and do not represent any degree of accuracy unless so stated by the designer.
在图纸标注尺寸时，除非设计者有意标明，注在尺寸线上的数字代表的尺寸仅仅是近似的，并不代表任何精度等级。
Drawing used to make final decision with basic mould messages such as structure, operation, main dimension, special requirements and so on.
具备模具结构、运作、主要尺寸、特别要求等，定案会议用图纸。
Is mechanical dimension PCB specification (Fab drawing) available at inspection station under document control?
PC B机械尺寸规格是否按照文件要求在检验站进行管控？
A dimension specified for a given feature on one level of drawing, (for example, a detail drawing) is not mandatory for that feature at any other level (for example, an assembly drawing).
一个图纸层面上的给定部品的尺寸(比如，细部图)并不能强制地标注在另外一个层面的图纸上(比如说，装配图)。
Drawing the mechanical engineering drawing usually need to mark the dimension tolerance of the parts.
绘制机械工程图经常要标注零件的尺寸公差。
The re-bar binding should be executed according to the requirements of the drawing. All specification, dimension, quantity and spacing should be checked correct.
钢筋绑扎将按图纸要求进行，所有规格、尺寸、数量、间距必须核对准确。
Dimension analysis and drawing steps of plane graphs;
平面图形的尺寸分析，作图步骤。
As per discussion there is 72 preliminary die drawing as attached file . Please advise which are critical area and dimension that IEC have to pay special attention .
附件里面是先前的72种设计的草图。请告知IEC所特别关注的区域和尺寸！
This paper presents a method to build the three dimension model of auto body parts in computer based on engineering drawing.
本文提出根据工程图纸建立汽车车身零部件计算机三维模型的方法。
According to dimension requirement of tapered roller bearing product drawing and actual situation of cage machining, the design method of assembling die is discussed.
根据圆锥滚子轴承产品图尺寸要求，结合保持架机械加工实际情况，探讨装配胎的设计方法。
The hardware system of three-dimension drawing bed was designed, which applied P89C51RD2 MCU as center of the controlling system.
以P 89c 51rd2单片机作为控制系统的核心对三维牵引床控制系统的硬件进行了设计。
Prior to installation, check first whether location of installation node, installation dimension and damper model etc meet the requirements of design drawing and documents.
安装前首先应核对安装节点的位置、安装尺寸、阻尼器的型号等是否符合设计图纸及文件的要求。
Details in motor's dimension drawing.
详见电机外形图。
Compared to cold drawing process, the cold rolling for high precision bars has certain distinct advantages: better surface finish obtained. superior dimension control and higher metal yield.
前言：冷轧法生产的高精度钢材较冷拔法具有更好的表面质量、尺寸精度和高的收得率。
In the fourth chapter, the automatic generation theory of the dimension chain based on assemble drawing is put forward.
第四章：提出了基于装配图约束关系的尺寸链自动生成原理。
The third drawing and dimension in the table underneath show parameters of WNtype flanges.
第三个图纸及其下面表格里的尺寸显示的是带颈对焊法兰的参数。
In the production of samples, we found that the dimension A1 shown in drawing can be guaranteed by machining only. Once after processing, such as: to oil, phosphate, pickling, the dimension change.
中文需要重新组织语言，改为“在制作样品的过程中，我们发现图中所示尺寸A1，在仅进行机械加工的情况下，完全可以保证，可一旦在此之后进行深加工，如：去油，磷化，酸洗之后，该尺寸会发生变化。
When working, coiled tubing is loaded by bending, drawing and inside pressure, so that it would bear three dimension stress.
连续油管在工作时除受卷绕弯曲和拉伸载荷作用外，管内常受到内压作用，承受三轴应力。
This paper discusses an automatic dimension algorithm for joint drawing in Steel Structure CAD system.
讨论钢结构设计中节点图的自动标注算法。
Some common drawing mistakes such as in representation of drawing, utilization of line styles, dimension label, description of section lines and technical structures are analyzed.
从图形表达、线型运用、尺寸标注、剖面线的表述和工艺结构等方面，剖析了常见的机械图样错误，并举例进行正误对比，提出了改进措施。
Dimension on drawings MUST be assotiative: It is forbidden to change dimension on drawing manually by annotation editor.
工程图上的尺寸标注必须关联：禁止通过“注释”来修改工程图上的尺寸标注。
An automatic dimension algorithm for joint drawing in steel structure CAD system is introduced in this pa-per.
文章介绍一种钢结构中节点图自动标注算法。
Drawing on a range of work in pragmatics, advertising and communication, this paper tends to make contribution to this particular communicative dimension of advertising language.
在借鉴大量与语用、广告及交际有关的著作及研究成果的同时，本文希望能对广告语言交际层面的研究作出自己的贡献。
To block stoping, mining system design mainly includes design of block parameter, design of pillar's dimension, design of ore drawing sequence.
对于阶段空场法，采矿系统设计主要包括采场结构参数、矿柱大小、回采顺序等。
In chapter 5, generation principle of the assembly dimension chain is presented faced to 3d CAD drawing.
第五章：提出了基于三维装配图的尺寸链自动生成策略。
Location of the speed reducer's and voltage's labels see motor's dimension drawing. The voltage in the label is AC220 ~ 240v.
减速器标签与电压标签按外形图所示位置粘贴，电压标签：ac220 ~ 240v。
In bulk deformation processes such as forging, rolling, extrusion, and wire drawing there is an intentional change in the thickness or the lateral dimension of the workpiece.
大部分的变形过程如：锻造，轧制，挤压和拉丝都有同样的过程就是有意使工件的厚度或外部尺寸发生变化。
A heuristic local search method based on variable priority is proposed to automate dimension and label placement of ISO drawing.
提出并实现了基于动态优先级的带回溯的标注位置搜索算法。
A heuristic local search method based on variable priority is proposed to automate dimension and label placement of ISO drawing.
提出并实现了基于动态优先级的带回溯的标注位置搜索算法。
应用推荐