Balance sheet is a static report, which shows the resources and distribution of the company's fund.
资产负债表是一张静态报表，反映了该报表截止时间时公司的资金来源及分布情况。
Softwares ANSYS and MATLAB were employed to analyze and simulate the velocity, pressure and shear stress distribution in sheet extruder dies based on the three-dimensional FEM.
利用ANSYS和MATLAB软件，对缩放型片材机头中熔体的速度、压力和剪切应力的分布进行三维有限元模拟和分析。
The energetic particles in the tail part of the Maxwellian distribution are then accelerated to a higher energy by the stochastic Fermi mechanism in the plasma sheet.
等离子体片中的随机费米加速机制，使麦克斯韦分布尾巴部分的高能量粒子被加速到更高能。
Comparing the calculated and experiment results show that the mathematical model is feasible and may be used to measure and study the velocity of sheet flow, sediment and the distribution of solute.
计算结果与实验结果比较表明此数学模型是可行的，有可能用于测量和研究水流速度、泥沙含量及溶质在水流中的分布。
The distribution of voltage and the flow of electric current within a field of the sheet are governed by the laws of potentials.
在该薄板的电场中，电压的分布以及电流的流动，均取决于电位定律。
A hybrid grid method was used to determine the principal plastic strain distribution in a deformed area of a sheet metal piece.
为进一步研究大型覆盖件冲压成形质量分析的技术，采用混合网格法进行变形区域塑性主应变分布测量。
The microwave brightness temperature(Tb) isoline, combined with the topographic contour line of ice sheet, interprets the characteristic of brightness temperature distribution in Antarctica.
结合微波亮温等温线图和南极等高线图分析了南极地区亮温分布的特点。
Please refer to the distribution FAQ sheet for any questions regarding distribution.
请参阅常见问题分配表的分配有关的任何问题。
A new approximate solution to thickness reduction of bending sheet is presented by considering the characteristics of deformation and stress distribution.
根据宽板弯曲过程中的变形与应力分布特征，提出了一种计算弯曲过程中板料厚度随弯曲程度变化的新的近似求解方法。
This instrument has been used to measure the sheet resistance distribution for Boron diffusion chip.
并用该仪器测定了硼扩散片的薄层电阻分布。
This instrument has been used for measuring the sheet resistance distribution for Boron diffusion chip.
并用该仪器测定了硼扩散片的薄层电阻分布。
On the basis of the sheet internal temperature changes in the plate and the thermal stress distribution.
在此基础上分析了板材内外部的温度变化情况及热应力分布情况。
Relationship between sedimentary facies and hydrocarbon distribution shows that most favorable oil and gas accumulation zones occur in the mouth bar, distal bar and sand sheet.
该区沉积相与油气分布关系分析表明，河口坝、远砂坝和席状砂微相是最有利的油气聚集带。
This position will be managing & growing our industrial AL sheet and coil business sales and profitability through distribution and direct sales.
通过分销和直销的方式，管理及提升通用工业铝合金板材，卷材的营业总额，并提高此业务的收益。
Some questions about Lamb waves in nondestructive testing of thin metal sheet were discussed in this paper. The calculation formula of energy distribution along thickness of sheet was advanced.
对金属薄板兰姆波探伤中的一些问题进行了探讨，提出了能量沿板厚分布的计算公式。
In this article, the principle and application of a new kind of instrument used to test the tensile stiffness index and fibre orientation distribution on a paper sheet were introduced.
本文介绍了一种用于实验室检测纸页纤维定向结构的新型仪器，分析了该仪器的基本原理、主要用途及对纸页抗张挺度检测的意义。
The flow track of liquid drip on packing sheet was also described. This can help the research of liquid distribution in packed bed.
并探讨了液滴在波纹板片上的流动轨迹，有助于对液体在这类填料层内分布作进一步研究。
The software ANSYS and MATLAB were employed to analyze and simulate the velocity, pressure, shear stress and viscosity distribution in fishtail sheet extruder die based on the three-dimensional FEM.
本文利用ANSYS和MATLAB软件，对鱼尾型片材机头中熔体的速度、压力、剪切应力和粘度的分布进行三维有限元模拟和分析。
The sheet steel for lighting distribution box is made into frameless shape, the main parts of which are shell, zero line bar, protective earth bar and panel etc.
照明配电箱用薄钢板做成无骨架形体，主要部件有壳体、零线排、保护接地排、面板等。
A lot of thin steel sheet bent parts are applied in high and low-voltage switchgear cabinets and various kinds of power distribution boxes.
高低压开关柜及各种配电箱，采用大量的薄钢板折弯零件。
The homogenization of sheet thickness distribution is improved. Finally, viscous pressure forming of conical part at room temperature and warm temperature were conducted.
分别进行了室温和加热时铝合金圆锥形零件粘性介质压力成形试验，试验结果与数值模拟具有相同的规律。
Channel and Sheet sand are sweet reservoir. Distribution of sand is controlled by provenance distance and palaeogeomorphology.
分流河道和席状砂为有利储层，砂体展布形态主要受控于物源远近及古地貌形态。
The results show that half-apex angle has a great effect on sheet thickness distribution, the smaller the half-apex angle is, the bigger the sheet thickness thins;
结果表明，半顶角对制件厚度变化起主导作用，其值越小，厚度减薄越严重；
The results show that half-apex angle has a great effect on sheet thickness distribution, the smaller the half-apex angle is, the bigger the sheet thickness thins;
结果表明，半顶角对制件厚度变化起主导作用，其值越小，厚度减薄越严重；
应用推荐