For example, to get the disk information for a remote host, you might use the command and get the output in Listing 1 below.
例如，要获取一台远程主机的磁盘信息，您可以使用下面清单1中的这个命令，并获得相应的输出结果。
This command creates one disk of 10gb size from the LSS 10.
这个命令将从LSS10中创建一个10gb大小的磁盘。
You just need to determine where the name of the second disk is and issue one command.
您只需要确定第二个磁盘的名称的位置，然后发出一个命令。
The results of the command, shown in figure 6, show that the files are successfully extracted to the local disk.
如图6所示，该命令的结果表明，这些文件已经被成功地解压到本地硬盘。
Running the same command after the migration shows that the virtual disk mappings have been automatically created, as part of the migration process.
在转移之后运行相同的命令，可以看到在转移过程中已经自动创建了虚拟磁盘映射。
Finally, if the CPU and disk conditions are met, the command is run and the next rule is processed.
最后，如果满足CPU和磁盘条件，则运行该命令并且处理下一条规则。
You can use this command to tell the system to boot from CD, disk, the network, or other devices.
可以使用这个命令让系统从CD、磁盘、网络或其他设备引导。
The ATAPI specification defines a command called IDLE IMMEDIATE that idles the HDD and retracts the disk heads to prevent them from hitting the platters.
ATAPI规范定义了一个名为 IDLE IMMEDIATE 的命令，它可以闲置HDD并收回磁头以防止它们触及盘片。
Use the WRKDSKSTS command to check the disk configuration and to verify that the disk utilization (% busy) is below the recommended threshold of 30%.
使用WRKDSKSTS命令检查磁盘配置，检查磁盘利用率（%忙）是否低于建议的 30%。
Thus a call from the audio driver to command the sound card will be accepted and processed but a call from the audio driver to command the disk will be rejected.
因此从声音驱动发出控制声卡的调用会被接受，而从声音驱动发出控制硬盘的调用会被拒绝。
VHD files can be mounted with either the command line tool Diskpart or via the Disk Management MMC snap-in.
VHD文件既能通过命令行工具Diskpart，也能通过磁盘管理单元来装载。
To create a raw disk image, use this command.
要创建原始磁盘映像，使用以下命令。
To directly copy from the source disk to the recordable disk, use this command
要直接将内容从源盘复制到可刻录盘，请使用下面的命令
Before extracting audit records from the db2audit.log file, flush any remaining audit records in the buffer out to disk by issuing the following command.
在从db2audit. log文件提取审计记录之前，发出以下命令将缓冲区中的所有审计记录刷新到磁盘。
To confirm that all the data (logical volumes) for each of the old hdisks had been migrated, I ran the LSPV command to list the contents of each disk.
为了确认每个旧hdisk的所有数据(本地卷)都已迁移完毕，运行lspv命令来列出每个磁盘的内容。
Any user can check their own quota limits and disk usage by running the quota command.
通过运行quota命令，任何用户都可以检查他们自己的配额限制和磁盘使用情况。
For example, you can use ls in combination with du to determine the disk usage of different directories with the command shown in Listing 5.
例如，使用清单5中的命令，您可以将ls与du组合使用，以确定不同目录的磁盘使用情况。
Then, I used the mirrorvg command to create an exact copy of the data on the new disk.
然后，我使用了mirrorvg命令来在新磁盘上创建数据的确切副本。
The qemu-img command creates disk images.
qemu - img命令生成磁盘镜像。
DISK_ADD: Triggered when a disk is added to the cluster (for example, using the chcluster command).
DISK_ADD：集群中添加磁盘时会触发(例如，使用chcluster命令)。
DISK_DELETE: Triggered when a disk is removed from the cluster (for example, using the chcluster command).
DISK_DELETE：集群中移除磁盘时会触发(例如，使用chcluster命令)。
Note that the command used takes as an argument the altered disk descriptor files from the mmcrnsd command above.
注意所使用的命令使用上面的 mmcrnsd 命令中的不同磁盘描述符文件作为参数。
This example loads the Apple Mac disk subsystem driver (called HFS) with the modprobe command.
这个例子，用modprobe命令为苹果机上的系统，添加一个磁盘子系统驱动模块。
When the new LUN had been assigned to the AIX host, the CFGMGR command was executed to pickup the new DS8300 disk.
当新的LUN已被分配给AIX主机时，会执行cfgmgr命令来发现这个新的DS8300磁盘。
To find the disk space being used by a single user, you need to combine du with the find command to only report disk usage for a specific user.
要查找某个用户所使用的磁盘空间，在使用find命令的同时，您需要结合使用du命令以仅报告特定用户的磁盘使用情况。
The mkintrd command is used to create an initial RAM disk image.
mkintrd命令用来创建初始的RAM磁盘映像。
The du command, instead of showing disk free space, shows disk usage information.
du命令并不是显示磁盘的空闲空间，而是显示磁盘使用情况的信息。
For a Unix system, you can use the command df -k to list all cooked disk devices on your system. Here is an example.
在Unix系统中，您可以使用命令df- k来显示系统上的所有成熟磁盘设备。
The data migration from the old disk to the new disk would be accomplished by the LVM command, migratepv.
使用LVM命令migratepv可以完成从旧磁盘到新磁盘的数据迁移。
The data migration from the old disk to the new disk would be accomplished by the LVM command, migratepv.
使用LVM命令migratepv可以完成从旧磁盘到新磁盘的数据迁移。
应用推荐