The total should be below the disk adapter throughput rating, usually less than 70 percent.
其总数应该小于磁盘适配器吞吐量速率，通常小于百分之七十。
The Custom configuration option allows advanced options, such as virtual disk adapter types, to be selected.
Custom配置选项允许选择高级选项，比如虚拟磁盘适配器类型。
If your server doesn't support disabling the local disk adapter directly, you can simply pull out your local hard disk physically.
如果您的服务器不支持直接禁用本地磁盘适配器，您可以卸下本地磁盘。
Edit file init or linuxrc to let your root file system disk adapter appear earlier than all other storage adapters in the same category.
编辑init或linuxrc文件，以使根文件系统磁盘适配器出现在同一个类别中的所有其他存储适配器的前面。
Configure the host adapter driver to be loaded through an initial RAM disk, which applies the configuration data for redundant disks when loading the adapter module at boot time.
配置主机适配器驱动程序，通过初始ram磁盘进行加载，初始ram磁盘将在引导过程中加载适配器模块时对冗余磁盘应用配置数据。
The current VIOS and LPAR FC adapter, DS8300 disk, virtual adapter and virtual disk configuration is also captured and used in the planning for the new disk assignments.
当前的VIOS和LPARfc适配器、DS8300磁盘、虚拟适配器和虚拟磁盘配置均被捕获并用在计划中以便进行新磁盘的分配。
Each physical link includes a host adapter in the primary disk subsystem and a host adapter in the secondary disk subsystem.
每条物理链路包括一个位于主磁盘子系统中的主机适配器，以及一个位于辅助磁盘子系统中的主机适配器。
This cannot be done if the disk is mounted on the Fibre Channel subsystem attached to an adapter that uses this driver.
如果磁盘被挂载在一个连接到使用该驱动程序的适配器的FibreChannel子系统上，那就无法执行这种操作。
The ANSI T10 standard provides a way to check the integrity of data read and written from the host bus adapter to the disk and back through the SAN fabric.
ANSIT10标准提供一种方法检查从主机总线适配器 （HBA）通过SAN 光纤写到磁盘和读取回的数据的完整性。
For example, if your root file system's physical disk is attached to a SAS adapter, then your init file may have a field like the following.
例如，如果根文件系统的物理磁盘与SAS适配器连接在一起，则init文件可以有如下所示的字段。
Here you can change the network adapter, disk mode options, and more.
在这里，可以更改网络适配器、盘模式（disk mode）选项，以及更多其他的属性。
Release: This command is issued by the owning host bus adapter when a disk resource is taken offline; it frees a SCSI device for another host bus adapter to reserve.
release(释放)：当磁盘资源下线的时候，这个命令由拥有该磁盘的总线适配器发送。这个命令释放该SCSI设备供其他总线适配器占用。
Change PCI Device Boot Priority to the adapter your root file system disk is using (as in Figure 2 below), if your Linux is installed on a local Planar SAS disk.
如果您的Linux安装在本地PlanarSAS磁盘中，请将PCIDeviceBootPriority更改为根文件系统磁盘正在使用的适配器(如下面的图2所示)。
Such an architecture would include a single hard disk, a single Fibre Channel adapter, or a single power source for any piece of equipment.
这样的一种架构通常只包含单个硬盘、单个光纤通道适配器或单个电源供所有设备共用。
The system was configured with 8 GB memory and one local disk drive. The network used a 1.0 Gbps Ethernet adapter.
系统配有8GB内存及一个本地硬盘，还有一个 1.0Gbps以太网卡。
The system was configured with 8 GB memory and one local disk drive. The network used a 1.0 Gbps Ethernet adapter.
系统配有8GB内存及一个本地硬盘，还有一个 1.0Gbps以太网卡。
应用推荐