It can gain the discharge parameter of tester.
可以获取检测仪的放电参数。
When discharge is full of discharge gap, each equivalent discharge parameter is around definite numerical value.
当放电充满整个间隙时,各等效放电参量在相同激励频率下基本保持在一定值附近。
A high speed data acquisition system for measurement of Micro EDM discharge parameter is designed. The hardware circuits are analyzed and discussed, also the software function is present.
设计了一个用于在微细电火花加工控制中放电参数检测的高速数据采集系统,对其硬件电路进行了分析和讨论,并给出了软件说明。
Users can set adjustable discharge power according to capability parameter and test request.
用户可根据性能参数、检测要求,设定调整放电功率。
Parameter test and load discharge can process at one time. It is controlled by CPU, and can automatically test three-phase voltage, current and power ETC.
参数检测和带载放电同时进行,单片机控制,可自动检测三相电压、电流、频率等参数。
The addendum coefficient is an important parameter in the designing the gear, and to affect the discharge characteristic of compound gear pump.
齿顶高系数是设计齿轮时的重要几何参数,也是影响复合齿轮泵流量特性的重要参数之一。
Partial discharge is important parameter for evaluating insulation ageing of high voltage electric appliance and equipment.
局部放电是评定高压电器设备绝缘老化程度的重要参数。
Partial discharge is important parameter for evaluating insulation ageing of high voltage electric appliance and equipment.
局部放电是评定高压电器设备尽缘老化程度的重要参数。
The discharge of debris flow is a basic parameter in debris flow preventing and controlling engineering.
泥石流流量是泥石流防治工程设计的基本参数,对泥石流危害性的评价研究具有重要意义。
The process of bubble motion changed by exploding wire parameter affecting the discharge power waveform is also viewed.
同时也得到了爆丝参数通过对能量波形的影响而改变气泡运动的过程。
According to the trend line formula of empirical and the chart of the spacial interpolation of hard rain parameter, maximum discharge of ungaged basins are confirm.
结合经验性参数趋势线、暴雨参数空间分布图与推理公式法确定无资料流域设计条件下最大清水洪峰流量和最大山洪洪峰流量。
It has discharge models of constant-current. After setting parameter, it can achieve capacity test to battery and load capacity test to DC power.
恒流放电模式,参数设定后自动完成蓄电池组的容量测试或直流电源的带载能力检测。
The effects of the discharge on the laser output characteristics were analyzed, and a preferable experiment parameter was presented.
分析了各阶段放电对激光输出特性的影响,并给出了较好的放电实验参数。
Voltage between tool and workpiece is an important parameter in the on line monitoring of wire electrical discharge machining (WEDM) process.
电火花线切割加工时工具(电极丝)和工件之间的放电电压是对放电加工过程进行实时检测的重要参数。
On the slope of the same gradient, soil erosion and hydrodynamic parameter increased slowly with the flow discharge.
坡度相同,坡面径流动力学参数及坡面侵蚀量随放水流量的增大而增加。
The uniformity of discharge gap is a very important technical parameter in lowering various interference factors and ensuring stable EDM process and quality.
在电火花加工中要降低各种干扰因素的影响,确保加工质量和稳定的加工过程,放电间隙的一致性是非常重要的一个技术指标。
This paper introduces the operation principle, structure of four-tooth outside chip discharge set of material device and main parameter determination of cutting amount.
介绍四齿外排屑套料装置的工作原理、结构及切削用量主要参数的确定。
Based on the optimized allocation of the sensors, the prototype dynamic test and parameter identification under flood discharge excitation for Ertan Arch Dam are carried out.
基于该传感器优化配置结果,开展了二滩拱坝泄洪振动原型动力测试和模态参数识别。
Monthly discharge was simulated based on the optimal parameter sets for both calibration and validation periods, and compared with observed values for effectiveness evaluation.
根据最优参数值模拟了率定期和验证期兴山水文站的月径流量,并与实际观测值进行了对比评估。
Monthly discharge was simulated based on the optimal parameter sets for both calibration and validation periods, and compared with observed values for effectiveness evaluation.
根据最优参数值模拟了率定期和验证期兴山水文站的月径流量,并与实际观测值进行了对比评估。
应用推荐