Discussed the plan of digital servo system.
论述了该数字随动系统的总体规划。
The function flow chart of this digital servo system is given, too.
并且给出了其数字伺服系统功能流程图。
Plug BEC from ESC, then digital servo into this card for offline use.
不接电脑，插接电变的BEC，及数位伺服机，离线使用程式卡。
Besides, digital servo system may also be applied to other frequency standards.
此外，数字伺服还可在其它原子频标中应用。
The Epsilon Series is the most compact digital servo drive in the Numatics lineup.
在小量系列是最精巧的纽曼帝克系列数字伺服驱动器。
Discussed the plan of digital servo system and several modes of digitalization interface.
论述了该数字随动系统的总体规划及武器数字化接口的几种方式。
In this paper, a high performance digital servo-system based on an embedded PC is studied.
本文研究了一种以嵌入式PC作为控制计算机的高性能位置伺服系统。
This paper introduces a digital servo control system for permanent magnet synchronous motor.
介绍了一种高性能的以永磁同步电动机为执行元件的全数字化伺服驱动器。
It is digital servo timing control system which is driven by PWM, direct current moment motor.
采用了脉冲调宽功放装置(PWM)，直流力矩马达直接驱动转台框架的数字伺服调速体制。
The operation principle and control method of electro-hydraulic digital servo valve are first introduced.
介绍了一种直动式电液数字伺服阀的结构原理及其控制方法。
In this paper, a high performance digital servo-system based on an industrial control computer is studied.
本文研究了一种以工控机作为控制计算机的高性能数字伺服系统。
In this paper a representation method of angles with numbers(16 bits)in digital servo systems is presented.
介绍了数字伺服系统中用十六位二进制数表示角的方法和误差角的计算。
In this paper a high performance digital servo control system for permanent magnet synchronous motor is studied.
研究了一种高性能的全数字永磁同步伺服系统。
This paper presents a project of modularization design for ground radar full digital servo system based on CAN bus.
介绍了一种基于CAN总线的地面雷达全数字伺服系统模块化设计方案。
SERCOS digital servo control system bus interface design and development of high research value and practical value.
数字伺服控制系统SERCOS总线接口的设计开发具有很高的研究价值和实用价值。
It analyzes the digital servo control system to control the process, structure, hardware and software implementations.
分析了数字舵机控制系统白勺控制过程、构造组成、硬件软件实现方案。
So the research and design of the digital servo valve is one of the most important aspects of nowadays hydraulic field.
因此在液压元件中数字伺服阀的设计与研究以及在它在具体领域中的应用是当今液压界的重要研究方向之一。
This article deals with the realization of a rapid position control of the digital servo system through double mode control.
本文研究用双模控制实现数字位置随动系统的快速控制。
In this paper, the DSP-based all-digital servo and driving system for the permanent magnet synchronous linear motor is proposed.
本文提出了基于DSP的永磁同步直线电机全数字伺服控制与驱动系统。
The angle coding technique takes a great part in the use of closed digital servo control system for detecting the offset of angle.
轴角编码技术在闭环数字伺服系统中反映角位置量方面有着极为重要的应用。
A new design problem in digital servo control system for structural characteristics of multi-joint robot and motion control features is studied.
分析了一种新型数字舵机控制系统白勺设计问题。
The problems are studied about the digital servo using Digital Signal Processor (DSP)for rewritable optical disk drives, and the system scheme is presented.
该文研究了可重写光盘机DSP数字伺服控制的问题，给出了数字控制系统的硬件构成。
A pneumatic servo loading system is proposed and a specially designed pneumatic digital servo valve is introduced in the system for the purpose of precise control.
为了达到这一要求，提出了气动伺服加载系统并引入特殊设计的气动数字伺服阀。同时对气动伺服加载系统进行数学建和模块化分析，最后进行了实验研究。
A pneumatic servo loading system was proposed and a specially designed pneumatic digital servo valve was introduced in the system for the purpose of precise control.
为了达到这一要求，提出了气动伺服加载系统并引入特殊设计的气动数字伺服阀。
The system takes photo-electricity coder as Angle position sensor, using brush DC motor as servo motor. The full-digital servo system is based on controller MCL2805.
采用光电编码器作为角位置传感器，以有刷直流电机作为伺服系统的伺服电机，使用控制器MCL2805实现全数字伺服控制系统。
This thesis puts forward a new direct-actuated digital servo valve, based on the studying relevant workings, and also advanced a new method modeling in hydraulic system.
本文在综述国内外电液数字控制技术及元件的相关研究成果的基础上，设计出了数字伺服阀的新型结构，并且提出了在液压系统中使用模块化建模的思想。
This thesis puts forward a new direct-actuated digital servo valve, based on the studying relevant workings, and also advanced a new method modeling in hydraulic system.
本文在综述国内外电液数字控制技术及元件的相关研究成果的基础上，设计出了数字伺服阀的新型结构，并且提出了在液压系统中使用模块化建模的思想。
应用推荐