Hardware system is made up of three modules: power supply circuit, digital control circuit and machine control circuit.
控制系统主要由电源电路、数字控制电路和机械控制电路三大模块构成。
Timing circuit is usually made up of power supply unit, panel circuit and timing board, it is the digital control part of power source.
定时电路一般由电源模块、面板电路和定时板组成，是功率源中的数字控制部分。
The application of digital technology to power supply control is one of the significant changes in power electronics industry in the recent years.
最近几年以来，数字技术在电源控制方面的应用是电源工业最重要的变化之一。
Digital signal processors (DSP) have been extensively used in areas of motor control and power switch supply control system.
数字信号处理器(dsp)已经广泛应用于电机控制、开关电源等领域。
It is shown by the experimental results that the inverter power supply with digital control technologies designed by this dissertation can output steady sine voltage.
实验结果表明：采用了本文设计的数字化控制技术的逆变电源，可以获得稳定的正弦电压输出。
The power supply adopts D/A mixed control and repetitive control. The digital part realizes the high precise waveform generator and the control based on voltage virtual value.
该电源采用数/模混合控制及重复控制方法，数字部分实现高精度的波形发生器和电压有效值控制；
The digital control of induction heating power supply was implemented through this design approach, and the software chart was illustrated as well in this paper.
通过这种设计方案，实现了感应加热电源的数字化控制，并给出了相应的软件框图。
This paper presents a digital controlled full bridge ZVS PWM switching power supply, which is based on sliding mode control method by using DSP.
本文以滑模变结构为控制核心，研制了以DSP为控制芯片的全数字化全桥移相软开关电源。
A novel distributed control scheme is proposed for the parallel operation of single phase digital controlled UPS (uninterrupted power supply).
提出了一种新型分布式控制方法来实现单相数字模块化ups(不停电电源)的并联运行。
The control system of IGBT induction heating power supply is designed based on DSP (digital signal processor) and CPLD (complex programmable logic device).
用数字信号处理器(dsp)和复杂可编程逻辑器件(CPLD)设计了IGBT感应加热电源控制系统。
This dissertation is focused on the research of the digital control technologies for uninterruptible power supply (UPS).
本文致力于单相不间断电源(ups)的数字化控制。
Magnet power supply with embedded DPSCM can achieve all-digital control, and achieve high precision DC stabilized power supply output accuracy control needs.
对于嵌入DPSCM的磁铁电源可以实现全数字化控制，并达到高精度直流稳流电源输出精度的控制需求。
This paper devotes to research the inverter power supply digital control technology.
本文致力于逆变电源数字化控制技术的研究。
Design the CAN bus address encoder, communication terminal digital display circuit, control relay circuit, LNK501 switching power supply chip circuitry.
设计了基于CAN总线的地址编码器，通信总站的数码显示电路，控制继电器电路，LNK501开关电源芯片电路。
The structure and the work principle of digital control pulse MIG welding invert power supply are introduced;
介绍了以DSC为控制核心的逆变交流脉冲MIG弧焊电源的构成及工作原理；
This paper presents a design about the remote power supply control circuit of WF-1006 digital seismic instrument's acquisition unit and gives a detailed introduction.
本文从电路设计的角度较详细地讨论了WF—1006多道遥测数字地震仪远端卸电线路的设计思想，以供同行们参考。
The computer control system hardware based on S7400 PLC, the system power supply, full digital 6RA70 DC drive configuration for the system and PROFIBUSDP field bus configuration are introduced.
提出了S7 400系列计算机控制系统的硬件配置、系统的供电方式、全数字直流调速系统6RA70的传动配置方案以及PROFIBUS DP现场总线的连接方式。
This paper I use TI's DSP chip design TMS320LF2407A type, a frequency inverter, I realized the main circuit power supply digital control, and improved output voltage accuracy and stability.
本文采用TI公司的TMS320 LF 2407a型DSP芯片设计了一种中频逆变电源，对电源主电路实现了全数字控制，提高了输出电压的精度和稳定度。
Finally, the technologic experiment of twin-wire welding was done with the equipment of twin-wire pulsed MAG high speed welding power supply and its multi-phase digital synchronic control system.
应用所研制的双丝脉冲mag高速焊多相位数字化协同控制电源装备进行了大量的双丝高速焊工艺试验。
Nowadays it is popular to use digital control in power supply design.
数字化控制电源已成为当今电源产品设计的潮流。
Nowadays it is popular to use digital control in power supply design.
数字化控制电源已成为当今电源产品设计的潮流。
应用推荐