The radiating element is arranged above the dielectric plate 1 grooving along the edge.
辐射单元位于介质板1上，沿边缘开槽。
The GRCS of dielectric sphere, dielectric plate and dielectric cube are calculated respectively.
以均匀介质球、有限长介质圆柱、均匀介质立方体为例进行了计算。
The S - matrix of the polarizer composed of circular waveguide and dielectric plate in arbitrarily states is given with rotation transform.
应用坐标旋转变换原理导出了介质片极化器在任意状态下的S矩阵。
T he result that the presence of dielectric plate inside CGG changes the mode order will be useful for the design of the microwave chemical reactor based on CGG.
分析表明介质加载时圆形槽波导的模式次序要发生变化，为设计圆形槽波导微波化学反应器提供了依据。
The effect of charges remaining on a dielectric plate upon the 50% impulse surface flashover voltage U_ (50) in the non-uniform field (rod-plane gap) is investigated.
针对不均匀电场(棒-板间隙)中绝缘板上残余电荷对50%冲击闪络电压u _(50)的影响做了一些试验研究。
The ground plate is arranged on one side of the dielectric plate 2 with a gap arranged at the middle, which is fed with the power to the radiating element through the gap.
接地板位于介质板2的一面，在中心开一缝隙，通过该缝隙对辐射单元进行馈电。
This antenna was divided into two parts: polarization-rotation grating and reflection- transmission grating etching on the paraboloid dielectric plate, which are designed respectively.
本文将天线分成扭转极化板栅条、抛物面反射透射栅条天线二部分，分别独立设计完成。
To analyze the formation of surface discharge on a dielectric plate under positive nanosecond impulse voltage in air, a wire to plane electrode system with a barrier of negative film was used.
采用感光胶片作为阻挡介质的针-板放电系统，解析空气中固体电介质上纳秒正脉冲表面放电的形成过程。
To raise ozone output of ozonator, it demands that ceramic plate materials for ozonator have good dielectric properties and quite high thermal conductivity.
为了提高臭氧发生器的臭氧产量，要求臭氧发生器用的陶瓷基板材料具有较高的介电性能和热导率。
The theory and method in measuring accurately the electronic and vacuum dielectric constant of parallel plate capacitor are introduced.
介绍了用电子分析天平测量平行板电容器两极板间的静电力和真空介电常量的原理和方法。
In the second part studied the fabrication process of dielectric resonator antenna model and high permittivity ceramic plate.
研究中的第二个部分，是对于微波介电陶瓷制备介电共振器天线与高介电陶瓷薄板之制程方面的研究。
The protection plate (10) is adapted to shield the first dielectric layer (14) from energy from the laser beam (52).
保护板(10)适于保护第一介质层(14)不受来自激光束(52)的能量。
The first plate electrode is formed on a second inner connection structure provided under the dielectric etch stop layer.
该第一平板电极形成于设于该介电蚀刻停止层下的一第二内连接结构之上。
The protection plate (10) is formed within the first dielectric layer (14) using a damascene process.
保护板(10)利用镶嵌工艺在第一介质层(14)中形成。
The second plate electrode is formed above the dielectric etch stop layer, and is approximately in parallel with the first plate electrode, and overlaps the first plate electrode.
该第二平板电极形成于该介电蚀刻停止层上，且大致的与该第一平板电极平行且相重叠。
Use ceramic materials as the dielectric, silver as electrode, and metal plate as shell.
用陶瓷材料做电介质，金属银做电极，金属极板做外壳。
With this equipment, the dielectric recovery strength characteristics of ceramic chambers and deion plate chambers are studied.
应用此装置测量了不同分断条件下陶土灭弧室和栅片灭弧室内的介质强度恢复特性。
The structure (1) comprises a fuse element (2), a protection plate (10), a first dielectric layer (14), and a second dielectric layer (4).
所述结构(1)包括熔丝元件(2)、保护板(10)、第一介质层(14)，以及第二介质层(4)。
The dielectric properties of peaches were measured during storage by using of LCR instrument, plate electrode and nondestructive measurement method.
利用智能lcr测量仪和平板电极系统，用无损检测方法测定了桃子在储藏过程中电特性的变化。
The paper introduces measurements about dielectric constant and tangential loss angle of a group of good function and high frequency printed electronic circuit plate with microstrip circuit.
介绍了利用微带电路来确定一组高性能、高频印刷电路板材料的介电常数和损耗角正切的方法，且给出了一组印刷电路板材料的特性测量值。
The second dielectric layer (4) is formed over the protection plate (10) and the first dielectric layer (14).
第二介 质层（4）在保护板（10）和第一介质层（14）上形成。
A second interlayer conductive joint hole is formed on and through the interlayer dielectric layer and is contacted with the second plate electrode.
该第二层间导电接孔形成于且穿过该层间介电层，且与该第二平板电极相接触。
A second interlayer conductive joint hole is formed on and through the interlayer dielectric layer and is contacted with the second plate electrode.
该第二层间导电接孔形成于且穿过该层间介电层，且与该第二平板电极相接触。
应用推荐