Of a dielectric the product of dielectric constant and the tangent of its dielectric loss Angle; a measure of the heating effect which occurs in dielectrics.
对于电介质来说，它是介电常数和介质损耗角的正切的乘积，这是对出现在电介质中的热效应的量度。
A method for measuring the dielectric constant and microwave loss of microwave ceramic with cutoff waveguide dielectric resonator is presented.
本文提出了用截止波导介质谐振腔测量微波材料相对介电常数和微波损耗的方法。
It was found that the dielectric constant and dielectric loss of unpoled samples is higher that those of poled samples.
结果表明：极化后的介电常数和介电损耗低于极化前。
The electromagnetic loss property was studied by the relative dielectric constant and relative magnetic permeability of the ferrites.
并测试样品的相对介电常数和相对磁导率，研究了它们的电磁损耗特性。
The electromagnetic loss property was studied by the relative dielectric constant and relative magnetic permeability of the above three ferrites.
经测试样品的相对介电常数和相对磁导率后，研究了它们的电磁损耗特性。
With the increasing of dopant content, grains grew up uniformly, and dielectric constant and loss increased.
随着氧化硼含量的增加，晶粒尺寸均匀长大、介电常数和介电损耗都增加；
The dielectric constant and dielectric loss of the composites rise with increasing the content of PANI.
复合材料的介电常数和介电损耗随pani含量的增加而上升。
The dielectric constant was almost a constant, while the dielectric loss and temperature coefficient of dielectric constant were sensitive to the sintering conditions.
随着烧结条件的不同，介电常数几乎不变，但介电损耗以及介电常数的温度系数则较为敏感。
The newly developed low loss, low dielectric constant and low temperature co fired ceramics (LTCC) materials are the best substrate for microwave MCM technology.
新开发的低损耗、低介电常数的低温共烧陶瓷(LTCC)材料最适合做微波mcm的基板材料。
The results showed that high dielectric constant and low loss BST film can be fabricated using this method without special anneal process.
使用这种方法不需要专门的退火工艺，就可以制备晶体结构完整的高介电常数BST薄膜。
It also showed that the complex dielectric constant and complex permeability decrease as the measuring frequency increasing, and maximum dielectric loss was 0.30, but magnetic loss is small.
其介电常数、磁导率基本都随测试频率的增加而下降；介电损耗值最大可达到0.30，磁损耗值较小。
The dielectric constant and loss increase with increase the content of graphite.
复合材料的介电常数和损耗随着石墨含量的增大而上升。
The effect of dielectric constant, dielectric loss factor, coefficient of thermal expansion (CTE)and characteristic impedance of substrate materials on properties of MMB are mainly discussed.
介绍了微波多层板所用基材的性能参数，重点阐述了材料的介电常数、介质损耗、热胀系数、特性阻抗对多层板性能的影响。
The paper introduces measurements about dielectric constant and tangential loss angle of a group of good function and high frequency printed electronic circuit plate with microstrip circuit.
介绍了利用微带电路来确定一组高性能、高频印刷电路板材料的介电常数和损耗角正切的方法，且给出了一组印刷电路板材料的特性测量值。
The important parameters for the wave absorption effects are electromagnetic loss factor, complex dielectric constant, complex magnetic conductivity.
评价吸波效能的主要参数是损耗因子、复介电常数、复磁导率。
From the point of improving the material properties, by the addition of carbonyl iron powder, it could improve its dielectric constant, but it also led to an increase in dielectric loss.
从提高材料介电性能的角度，羰基铁粉的加入提高了其介电常数，但同时也导致其介电损耗的增加。
Maintains small dielectric constant and dielectric loss at high.
高温和高频时介电常数和介质损耗都小3。
The loss is greater when the imaginary part of the complex dielectric constant is bigger and the mode order is higher.
介电常数虚部大（绝对值），而且包层模序也大时，损耗较大。
The piezoelectric strain coefficient and the dielectric constant of PVDF films increased, and the dielectric loss decreased with the increasing of the polarization field.
随着极化电场的升高，PVDF压电薄膜的压电应变系数升高，介电常数升高，介电损耗降低。
The piezoelectric strain coefficient and the dielectric constant of PVDF films increased, and the dielectric loss decreased with the increasing of the polarization field.
随着极化电场的升高，PVDF压电薄膜的压电应变系数升高，介电常数升高，介电损耗降低。
应用推荐