The earth is flat and you'll die if you go over the edge.
地球是扁平的，你要是走过了它的边缘就会有生命危险。
The gap between the minimum cutting edge cutting, trimming punching die when the distribution width is small, these are to be noticed.
刀口模切割线间的间隙最小，冲孔模修整时的分布宽度也很小，这些都是要注意的。
The distributing of intensity of pressure is determined when polished die is baring partly and the controlling means of edge effect are generalized.
确定了抛光模露边时压力的分布情况，总结了边缘效应的控制方法。
We can go along the edge of the whirlpools, and the boat will like drawing a circle, and we should throw the anchor into the water as soon as we get close to the island, or we will die.
我来展示一下吧。我们可以从漩涡的边缘通过，船就会像在绕圆圈一样，当我们绕到靠近岛的地方时，我们应当立即抛下船锚，否则我们就会死。
A ferocious ghost is compelling two people to die the edge.
一具穷凶极恶的鬼魂正将二人逼上死亡边缘。
The crack appears at the edge angle due to stress concentration caused by alternating load, which finally leads to the fissuring of die plate.
凹模在使用过程中，由于交变载荷的作用，使碳化物的棱角处应力集中出现裂纹，最终导致凹模开裂。
This paper introduces the design of the cutting edge section, selection of its geometrical parameters and application of the stamping cutter-die used for blanking the nonmetallic materials.
介绍了非金属材料落料用切刀式冲模刀刃截面的设计、几何参数选择与应用。
According to the blanking distortion procedure, the theory that decide the proper gap is to make sure the edge of the male die and female die's gap can be superposition.
由冲裁变形过程的分析可知，决定合理间隙值的理论依据是应保证在塑性剪切变形结束后，由凸模和凹模刃口处所产生的上、下剪切裂纹重合。
I've only had one method die a quick death. I attributed that to a book that explained the edge.
我只有一个办法，我把它归因于一本书对“边界”的解释。
Return springs and rods must be adequately protected from handling damage if they extend beyond the edge of the die shoe.
如果驱动弹簧及锣秆伸出模座外应充分的保护避免搬运破坏。
In designing of the die pattern, a high-speed die-changing structure can be applied to die with the inclination edge to raise the efficiency of blanking.
在模具结构设计方面，斜刃口模具可采用快速换模结构，以提高生产率。
The design method of faceplate oblique edge blanking die, die structure, punch structure and matrix structure were introduced in detail.
介绍了硅钢片硬质合金复合冲模与凸模、凹模、凸凹模等的制造方法。
This machine is one of corollary equipment for making steel blade die cutting plate. It is used to trimming and cutting for die cutting ruler and creasing rounded edge after modelling.
本机是制做钢刀模切版过程中的配套设备之一，它可广泛用于切线刀，压痕线在成型后的修整、切断。
The shape of the male die cutting edge was determined by experiment. The products punched had minimal burr and smooth section.
通过试验确定了合理的凸模刃口形状，冲出的零件毛刺极小，产品断面平整光滑。
This machine can fulfill the processes such as paperboard printing (1~5 colors), creasing, edge trimming, slotting, corner cutting, hole punching and die cutting etc in one cycle automatically…
能一次完成纸板1—5色印刷、压线、修边、开槽、切角、打孔、模切等多道工序。
Special designed reduction mechanism when board arrives at the front resister, can ensure regular lead edge when the board arrives at the front register, thus to assure die-cutting precision.
独特设计的纸板到达前规处减速机构，能够保证纸板到达前规纸边前缘平整，确保模切精度。
The grooving die set is composed of a punch edge and a groove edge which have the same shape.
开槽模具由具有形状相同的冲头刃、槽刃组成。
The grooving die set is composed of a punch edge and a groove edge which have the same shape.
开槽模具由具有形状相同的冲头刃、槽刃组成。
应用推荐