• The stamping process planning plays an important role for the die design.

    冲压工艺设计是冲模设计过程中的关键一环。

    youdao

  • The factory possesses strong capacity for metal die design, manufacture and press process.

    我厂拥有较强的五金模具设计制造和冲压加工能力。

    youdao

  • It shows that rational die design and billet size can effectively prevent the defects from further enlarging.

    研究表明:通过合理设计锻模,选择适当的坯料尺寸,能有效防止锻件内部冶金缺陷的进一步扩大。

    youdao

  • Numerical simulation provides the engineers powerful tool to solve complex die design problems of sheet forming.

    数值模拟技术为工程师解决复杂的板料成形模具设计问题提供了强有力的分析工具。

    youdao

  • The study can provide the reference for the die design and technology design of precision forging of spiral bevel gear.

    研究结果可为弧齿锥齿轮温锻成形的模具设计、工艺方案制订提供理论依据。

    youdao

  • The punching die design of external bracket of car pump is elaborated.

    详细论述了轿车油泵外用支架的冲压模具设计过程。

    youdao

  • Thus the all fiber forging technics is presented and the die design is made.

    为此提出了全纤维锻造工艺,并进行了模具设计。

    youdao

  • The flow model of extrusion and optimal principles of die design are discussed.

    讨论了挤压流动模型、凹模优化设计原理。

    youdao

  • The low-pressure casting process and die design for automobile housing were introduced.

    介绍了汽车壳体零件低压铸造工艺与模具设计。

    youdao

  • The article has introduced the cross wedge rolling preforming technology and its die design.

    介绍了楔横轧制坯工艺及其模具设计。

    youdao

  • Strip layout is the key procedure in progressive die design, it is known as a NP hard problem.

    级进模工步排样是级进模设计的核心,理论上属NP完全问题。

    youdao

  • The technology and the die design of cold extruding for the electric hammer drill is described.

    介绍了电锤钻头冷挤压工艺及模具设计。

    youdao

  • The good quality, low costs and short cycle of die design can be practiced by CAD system of die.

    模具CAD系统使模具设计的高质量、低成本、短周期的实现成为可能。

    youdao

  • We should seek for an optimal combination of technical effect and economical profit in die design.

    设计模具应追求技术效果和经济效益的最佳组合。

    youdao

  • Extrusion die design for compound triple-layer plastic pipe by two extruding machines is introduced.

    介绍用两台挤出机共挤复合三层塑料管材机头的模具设计。

    youdao

  • The features of die design are discussed and a conceptual model is proposed for series design of die.

    本文在对模具设计进行分析的基础上,提出了模具设计特有的系列化设计概念模型。

    youdao

  • So it is very necessary to exploit a practical CAD system for panel trimming and punching die design.

    所以,针对覆盖件开发一套实用的修边冲孔模cad系统无疑是十分必要的。

    youdao

  • The effect of die design on coating concentricity of optical fiber at high drawing speed is investigated.

    研究了在高速拉丝条件下涂覆模具的设计对光纤涂层同心度的影响。

    youdao

  • The flow state analysis of the plastic melt in the extrusion die is the basis of the extrusion die design.

    塑料熔体在挤出模中的流动状态分析是挤出模设计的基础。

    youdao

  • The basic method for aided design on microcomputer is discussed. The mutual CAD system for die design is set up.

    论述了在微机系统上辅助设计的基本方法,建立了模具设计的交互式CAD系统。

    youdao

  • The die design critical points and advanced pressing process of board spring on rotating shaft steamer dynamotor.

    介绍了汽轮发电机转轴上的板弹簧模具设计要点以及先进的压制工艺。

    youdao

  • A case of punch die design is finally presented to verify the effectiveness and feasibility of the proposed method.

    最后以冲裁模具设计过程为例,验证了上述方法的有效性和实用性。

    youdao

  • In die design, the pressure center of stamping die is calculated generally using analytic method or schematic method.

    在模具设计中,冲裁模压力中心通常采用解析法或图解法求解。

    youdao

  • New rotary rolling technology, equipment selection and die design for Model EQ140 auto semi-axle has been introduced.

    介绍了EQ 140汽车半轴摆辗新工艺、设备选择及模具设计要点。

    youdao

  • A dissertation is made on the process and main points of the die design for extruding the hollow parts of the frustum type.

    本文论述了锥台形空心件挤压成形工艺和模具设计要点,给出了实用的模具结构。

    youdao

  • In die design, the blanking pressure center of stamping die is calculated generally using analytic method or schematic method.

    在模具设计中,冲裁模压力中心通常采用解析法或图解法求解。

    youdao

  • Discuss punching small thread fluted opening technology, die structure, die design and die manufacture technology on thin sheet.

    论述了在薄板冲压件上,用变薄翻边冲制小螺纹底孔的工艺、冲模结构、设计与制作技术。

    youdao

  • The hot extruding forming technology and die design of high-voltage switch component LW8-35SF6 aluminum alloy pull-rod are analyzed.

    分析了高压开关零件LW8 - 35sf 6铝合金拉杆的热挤压成形工艺及模具设计。

    youdao

  • The selection method of roll forging process parameters of middle tonnage automobile front axle and die design outline were stressed.

    论述了中吨位汽车前轴辊锻成形工艺参数的确定方法和模具设计要点。

    youdao

  • The selection method of roll forging process parameters of middle tonnage automobile front axle and die design outline were stressed.

    论述了中吨位汽车前轴辊锻成形工艺参数的确定方法和模具设计要点。

    youdao

$firstVoiceSent
- 来自原声例句
小调查
请问您想要如何调整此模块?

感谢您的反馈,我们会尽快进行适当修改!
进来说说原因吧 确定
小调查
请问您想要如何调整此模块?

感谢您的反馈,我们会尽快进行适当修改!
进来说说原因吧 确定