The first set is blanking and punching compound die.
第一组是消隐和冲压复合模。
Introduced a kind of compound triming die with connecting rods, it could finished the piercing and triming and sizing process in one press, the working efficiency is high, triming quality is good.
介绍了一种复合式连杆切边模，可在压力机一次行程过程中完成连杆的冲孔、切边和整形工序，该模具具有工作效率高、切边质量好等优点。
Lisa : Better for them to die than to let them compound their sins. Begin by slaying that one, over there.
丽：让他们背负罪孽还不如让他们死去。就从那个开始杀掉，那边。
Through analyzing the forming process of the parts, a new_conception and practical compound forming die with simple structure for floating slides was introduced.
通过对工件的成形工艺分析，介绍一种构思新颖巧妙，结构简洁实用的浮动滑块复合成形模具设计。
Extrusion die design for compound triple-layer plastic pipe by two extruding machines is introduced.
介绍用两台挤出机共挤复合三层塑料管材机头的模具设计。
The design describes the structure of compound die stamping flip-chip design and working process.
本次设计阐述了冲压倒装复合模的结构设计以及工作过程。
The construction of once-formed compound repositioning die is also adopted to guarantee the quality of the product, raise the production efficiency and decrease the cost of production.
并采用一次成形的复合复位模结构，既保证了产品的质量，又提高了生产效率，同时降低了生产成本。
In the conditions of assuring reliability and life of die, much more economic benefits could be obtained by improving the compound degree of die.
在保证可靠性和一定使用寿命的前提下，适当提高模具的复合程度，可大大提高经济效益。
This paper analyzed technological peculiarities on the step part, designed a drawing and extruding compound die. It can improve the part quality and benefit.
通过分析零件的工艺特点，设计了拉伸挤压复合模，不仅可提高零件质量，而且可提高生产效率。
Introduced design of the adjustable blanking-drawing compound for the drawing with flange, the drawing die could adjust the flange size, and satisfied the part tolerance requirement.
介绍了带凸缘拉伸件可调式落料拉伸复合模设计，实现对凸缘直径尺寸可以进行调整以实现一定公差要求的模具结构。
According to parts character, a pair of assembled punching, blanking compound die punching is designed, die structure is introduced, and assembled carling compound die structure is stated as well.
根据零件特点设计了一副组合式的冲孔、落料复合模冲压两种产品，介绍了模具结构，论述了组合式纵梁复合模的结构特点。
The bending and pressing convex forming compound die for locking spring is designed, the die structure and pressing process are introduced, the product quality and production efficiency are improved.
针对锁紧片零件，设计了折弯压凸复合模，并介绍了模具结构和工作过程。提高了产品质量以及生产效率。
Improved properly such mechanisms as the location, stripping and scraps treatment, the common compound die was satisfied the need of the automatic stamping.
对普通复合模的定位、卸料以及废料处理等装置加以适当改进，满足了自动冲压的需要。
The structural design, design parameters, material chosen and manufacture process of multi-pinhole compound die of main printed circuit board for large screen color TV are introduced.
介绍大屏幕彩色电视机主印制板多小孔复合模的模具结构、设计参数、材料的选用和制造工艺等。
As styling method of compound curved surface has been widely used in die surface styling, it possesses a very important position in surface styling of motor vehicle body cover panels.
由于混合曲面的造型方法在模具表面的造型中广泛采用，从而使混合曲面的造型方法在汽车覆盖件表面造型中占有很重要的地位。
Mainly introduced the detailed structure and working process and the technology analysis of the blanking-drawing-extruding compound die for the stainless steel whistle pot cover.
主要介绍了不锈钢球形响壶盖的落料、拉伸、挤边复合模的详细结构、模具工作过程、工艺分析。
The structure, main design parameters and work process of the compound die installed on single action press and working for blanking and drawing with constant blank holder pressure were presented.
介绍了用于单动压力机的新型恒压边力落料拉伸复合模的结构及主要设计参数和模具工作过程。
Many methods to reduce working procedure reasonably and to improve the compound degree of stamping die were described by enumerating many kinds of special structure of die.
通过列举各类特殊的模具结构，介绍合理减少工序数，提高冲压模具复合程度的各种措施。
In addition, both the working process of compound die and questions required attention are stated.
同时也阐述了复合模工作过程及注意事项。
Adopting once punching process and using fewer cost and worse plasticity leftover material finish twice drawing of compound die.
分析了小圆角圆筒件的成形工艺性，利用成本较低、塑性较差的角料，采用一次冲压工序完成二次拉伸的复合模。
By adopting the compound mold of die mold, furan resin sand and graphite sand, the heavy duty thin wall complex Al-alloy castings have been successfully produced.
采用金属型、呋喃树脂砂、石墨砂等复合铸型，成功生产了大型、薄壁、复杂铝合金铸件。
Then layout design and various process forces of calculation is introduced. Finally drawing and extrusion compound dies is adopted to make die structure better rationalization and effectiveness.
并进行了排样设计和各种工艺参数的计算，最终采用拉深、挤边复合模具，可使模具结构更为合理而有效。
Through the analysis of forming technology of regulator of left chair, the method of using two sets of compound die is put forward. The specific die structure and its work pro - cess are introduced.
通过对左座椅调整器的成形性工艺分析，提出了采用两套复合模结构的方法，并介绍了模具的具体结构及模具工作过程。
A die casting die with pumping crossed cores by crossed compound dog-led cams and hydraulic pressure is used for cupulate parts with inboard concave.
交叉复合弯销与液压抽拔交叉型芯压铸模结构，用于压铸带内侧凹的杯形零件。
A curling compound die for the hinge used for the plate-bending machine was introduced. The structure characteristics of the die and the attention problems in the design of the die were discussed.
介绍了一种适用于折板机的铰链卷圆成形复合模，讨论了该模具的结构特点和设计中应注意的问题。
The stress analysis of compound female die is a very complicated problem. Its accurate analysis is the key to solve die longevity.
组合凹模的应力分析是一个非常复杂的问题，对其进行精确分析是解决模具寿命的关键。
The application of the Shared plate technology effectively lowered the cost of the compound die and shortened the manufacturing cycle.
共用模板技术的应用，有效地降低了复合模成本并缩短了制造周期。
This is a introduction to the Pulse Current electrolytic machining of forging die equipment using low density compound electrolyte, and examples are also given.
介绍了使用低浓度复合电解液，锻模的脉冲电流电解加工的设备及加工实例。
The main points for the design of the compound die were introduced. The compound die has prominent advantages on the production of series products and on speeding up the production cycles.
通过介绍复合模的设计及要点，阐明了复合模对于系列化产品的生产，加快产品的投产周期，具有显著的效果。
The main points for the design of the compound die were introduced. The compound die has prominent advantages on the production of series products and on speeding up the production cycles.
通过介绍复合模的设计及要点，阐明了复合模对于系列化产品的生产，加快产品的投产周期，具有显著的效果。
应用推荐