The discharge of seepage per unit width q is lower than or equal to the allowable design discharge (in consideration of storage and exploitation of water energy).
单宽渗流量小于或等于允许设计渗流量（以蓄水水能利用为原则）。
The many indefinite exists in the design parameters and influence factors of the working stress and allowable stress of the roller movable teeth drive.
滚子活齿传动设计中，在工作应力、许用应力的设计参数和影响因素中存在着许多不确定性。
The allowable stress of the pipe material shall be chosen from the data of GB 50316 Design Specification for Industrial Metal Piping.
管子材料的许用应力可按GB 50316《工业金属管道设计规范》中的数据选用。
The obtained lowest allowable flowing pressure value can be used as an important basis for allocation and design of an oil field.
得到的最低允许流动压力数值可作为油田配产和油田规划设计的重要依据。
Through analysis, we consider that the spiral case of left powerhouse units works normally, and that the stress and deformation are within the range of allowable design.
通过分析认为左厂房机组蜗壳工作性态正常，应力和变形均在设计允许范围内。
On the basis of statistical analysis, a method of determining the allowable design values is proposed.
在统计分析的基础上，给出确定设计许用值的方法。
If the design is based on the strain hardened properties, the allowable design stress will usually be above the actual yield point of the HAZ.
如该设计基于应变硬化性能，设计应力通常在HAZ实际屈服点以上。
At last, under the allowable stress with ANSYS to optimize the design of the final model and gain a new kind of horn with resonance of 12.35.
最后借助ANSYS优化设计模块进行仿真实验，在材料许用应力下对变幅杆进行优化设计，获得了谐振比达12.35的新型变幅杆。
Ultimate strength design is not required and the reinforcement can be determined only on basis of allowable crack width in design of beam on foundation.
地基梁可不进行承载能力极限状态的计算，其配筋可由正常使用极限状态中的允许裂缝宽度来确定。
According with the allowable stress design theory, the wind loads and load-carrying capacity of antenna struts are calculated, and their inter forces are analyzed.
根据容许应力设计理论，对天线撑杆的风荷载和承载能力进行结构计算，并对天线撑杆进行内力分析。
Various factors should be considered in determination of the allowable maximum heat loss, so as to ensure rational insulation structure design and insulation effect evaluation.
本文只讨论保温的设计方法与最大允许热损失量进行探讨。
The results indicate that it is conservative to design CFST arch Bridges by using allowable stress method in steel tube, and that it is reasonable to use limit state method.
数例表明，目前广泛应用钢管应力控制CFST的设计过于保守，文中方法似更合理。
These formulas more actually reflect the strength characteristics of massive concrete and visually show allowable design stress of concrete under certain operation state.
公式较真实地反映了大体积混凝土的强度特性，直观地表明了在某运行状态下混凝土可容许承受的应力。
Strength Design values may be converted to Allowable Stress Design values.
设计要求、强度设计值可转换为许用应力设计值。
Strength Design values may be converted to Allowable Stress Design values.
设计要求、强度设计值可转换为许用应力设计值。
应用推荐