Strain, or unit deformation, is defined as the unit change in the size or shape of material as a result of force on the material.
应变或者单位变形是材料上的压力造成材料大小和形状的单位改变量。
Socket joint is adopted between the plates, which can allow the inter-story drift and unit deformation and withstand substantial building movement.
板块之间采用插接方式连接，能吸收层间变位及单元变形，可承受较大幅度建筑物移动。
The deformation of spindle unit of machine tool affects processing accuracy of the spindle.
机床主轴单元的变形影响主轴的加工精度。
A valid method to make the anisotropic deformation behavior of load bearing unit clear is to research principal stress and principal strain relationship, and true triaxial test is a necessary means.
弄清受荷单元的主应力主应变关系是认识各向异性变形性状的有效方法，而真三轴试验是必要的手段。
The defects and uneven force subjecting condition of the structural design may cause the deformation and damage of the unit frames, resulting in dropping and damaging of the instruments.
结构设计的缺陷和不均衡受力状况都可能导致仪器房框架结构的变形甚至损毁，导致仪器设备脱落或损坏。
Based on the basic hypothesis, the shock wave pressure emerging in the medium after the jet punctures the armor unit is estimated, while deformation of the armor unit plate and the jet are calculated.
并在基本假设的基础上，对射流击中装甲单元后在介质中产生的冲击波进行了压力估算，及装甲单元的壁板变形和射流变形的计算。
This article illuminates the deformation of welding clapboard on turbine machine 200mw, and its damage to the unit, which often occur in domestic power plants.
阐述了200MW汽轮机焊接隔板变形这一在国内电站中多次出现的问题，以及由于隔板变形而对机组带来的危害。
They are the changing values of vertical velocity per unit distance along the horizonal direction on the sur-facial deformation field in which crustal vertical movement is dominant.
它是指在由发震构造引起的垂直运动为主的地表形变场中，水平方向上单位距离内垂向速率变化的物理量。
After cause analysis of the pipe deformation inside cold box, some corresponding precaution measures are proposed from the aspects of design, fabrication and operation of air separation unit.
文章详细分析了空分设备冷箱内管道变形的原因，从空分设备的设计制造和操作方面，提出了相应的防范措施。
The model of representative unit cell (RUC) is used to numerically simulate the deformation, instability and collapse of single-mode aluminum honeycombs under uniaxial compression.
采用结构代表胞元模型数值模拟了在不同相对密度范围的单型铝蜂窝结构在单向压缩过 程中的变形、失稳和破坏现象。
The horizontal deformation was not also remark able in any unit of North China.
水平形变在各单元内部也不显著；
Based on the 300mw unit, calculations of high pressure inner cylinder on different typical conditions are carried out, and the deformation trends are concluded.
以300MW汽轮机组为对象，对高压内缸进行几种典型工况的分析计算，得出了高压内缸在不同工况下的径向变形趋势并分析了变形原因。
By means of drawbead unit simulation experiment, the deformation regularity and characteristics of sheet metal in drawbead have been revealed.
通过拉延筋基本单元模拟试验，揭示了板料在拉延筋内的变形机理和变形特点；
The protuberant bases formed by utilizing the unit knife blades increase the anti-deformation intensity, can adopt thinner steel plates for blanking, and reduce the cost of materials.
利用单元刀片形成的凸座增加防变形强度，而能采用较薄的钢板来冲裁，降低材料成本。
The protuberant bases formed by utilizing the unit knife blades increase the anti-deformation intensity, can adopt thinner steel plates for blanking, and reduce the cost of materials.
利用单元刀片形成的凸座增加防变形强度，而能采用较薄的钢板来冲裁，降低材料成本。
应用推荐