In normal use case, if the KFC door if deformation, it is likely due to the use of aluminum alloy material quality difference and thickness lead.
在正常使用情况下，肯德基门若出现变形，很可能是由于使用的铝合金型材原料质量差和厚度过薄导致。
A new approximate solution to figuring out thickness reduction in bending sheets is presented in views of the characteristics of deformation and stress distribution.
根据宽板弯曲过程中的变形与应力分布特征，提出了一种计算弯曲过程中板料厚度随弯曲程度变化的新的近似求解方法。
The Mannesmann barrel-shaped rolls can be designed arid processed easily, but it makes the non-linear deformation zone in skew-rolling and leads to the inhomogeneous wall thickness.
曼乃斯曼桶形轧辊设计简单，加工方便，但形成非线性的斜轧变形区，导致壁厚不均。
The results show that the plastic deformation is obviously different from that of bulk metal and the thickness plays a key role on the ductile to brittle transition in al interlayer.
结果表明：中间纯铝层的塑性变形行为明显不同于块体纯金属，其厚度尺寸对材料的韧脆转变具有显著影响。
In bulk deformation processes such as forging, rolling, extrusion, and wire drawing there is an intentional change in the thickness or the lateral dimension of the workpiece.
大部分的变形过程如：锻造，轧制，挤压和拉丝都有同样的过程就是有意使工件的厚度或外部尺寸发生变化。
The deformation of rock layers in which the thickness of each layer, measured perpendicular to initial (undeformed) layering, is maintained after the rock layers have been folded.
在垂直于原始的(未形变的)层面量测的每层厚度，在岩层褶皱之后仍保持不变的岩石形变。
The various methods of measuring the film thickness of the deformation zone in rolling are studied and a new "heating 'method of measuring the film thickness are developed."
就轧制变形区油膜厚度的不同测试方法进行了对比研究，提出了简便、实用的加热退火法。
Sheet thickness is thinned, surface area is increased in the nc incremental sheet metal parts forming process, and sheet forming point by point is to lead to the whole sheet deformation.
认为，板料零件数控渐进成形是使板料的厚度减薄，表面积增大，靠逐次的变形累积产生整体的变形。
The thin thickness small diameter brass antenna casing is introduced and plastic deformation theory in tension fracture process is analyzed.
介绍了开发研制的黄铜薄壁小直径天线套管，并对拉伸断裂的塑性变形理论进行了分析探讨。
The influences of strip thickness, forward and backward tension, reduction ratio and resistance to deformation on the edge drop were investigated in detail.
详细研究了带钢厚度、张力、压下率、变形抗力等对边缘降的影响。
A higher pressure of the inlet fluid will result in the increases of thermo-elastic deformation and the balancing film thickness.
流体注入压力越高，热弹变形量越大，密封端面平衡间隙亦越大。
The uniformity of deformation during hot rolling could be improved by properly increasing the slab thickness and adopting large reduction rate in first several rolling passes.
适量增加铸坯厚度，并在较靠前的机架分配较大的压下量有利于提高轧制过程的应变均匀性。
However, the deformation is more uniform with regard to billet in contact with the work surface of punch, material thickness decreases less, therefore, the purpose of calibration has been reached.
而与模具工作表面相接触的管坯，其变形则较为均匀，材料壁厚减薄较小，达到扩径整形的目的。
When in use of the lens thickness gauge, the force bearing area of the lens is greater, thereby avoiding the measurement errors caused by the deformation due to the local force bearing of the lens.
使用该透镜测厚仪时，透镜的受力面积较大，从而可避免透镜局部受力产生形变而造成的测量误差。
When in use of the lens thickness gauge, the force bearing area of the lens is greater, thereby avoiding the measurement errors caused by the deformation due to the local force bearing of the lens.
使用该透镜测厚仪时，透镜的受力面积较大，从而可避免透镜局部受力产生形变而造成的测量误差。
应用推荐