Works of art and design shape and deformation in the main realistic.
艺术设计作品的造型以写实和变形为主。
Strain, or unit deformation, is defined as the unit change in the size or shape of material as a result of force on the material.
应变或者单位变形是材料上的压力造成材料大小和形状的单位改变量。
The objective of this article is mostly using characteristic of Shape Memory Alloy (SMA) to control the thermal deformation of antenna at orbit, ensuring the precision of antenna in a certain range.
本文的主要目的是利用形状记忆合金的特性控制在轨天线的热变形，以此来保证天线的精度在一定的范围之内。
Punching is a kind of pressure process method that punching dies are used in press sheet to put pressure on the plastic deformation or separation, for a certain shape and size of components.
冲压是利用冲压模在压力机上对板料或热料施加压力使其产生塑性变形或分离，以获得具有一定形状和尺寸的零件压力加工方法。
It was the above two reasons that make the improvement in shape memory effect through aging after deformation much more remarkable than through aging free deformation.
正是这两方面的原因导致变形后时效对合金形状记忆效应的提高比不变形直接时效的高得多。
In shape theory, the three-dimensional deformation theory of plate and strip rolling is an important and difficult study content.
板带轧制的三维变形理论是板形理论研究的重点和难点。
To general problem of the slab head bending in rolling, the effect of geometric shape coefficient of the deformation zone and entry Angle on head bending is researched.
本文针对中厚板轧制过程中因头部翘曲而影响产品质量和产量这一生产中普遍存在的问题，研究了变形区几何形状系数和送入角变化对轧件头部翘曲的影响。
The shape of vertical section with settlement deformation is in highly accordance with the shape of top silty clay layer before unloading.
卸载前沉降变形纵剖面形状与粉质粘土层顶板面形状非常一致；
Management and trust crisis are in deformation, being out of shape and Losing patterns of characters of leaders.
管理与信任的危机在于领导者人格的扭曲、变形和失范。
Describing the inverse as a minimum problem, in view of a example-based skin deformation plan, we have proposed a unified model that incorporating the shape interpolation.
通过以一个极小值问题来描述反转过程，针对基于实例的皮肤变形方案，本文提出了一个可以整合形状插值的统一模型。
Major causes of cracks are contraction deformation in early stage, too complicated and changeable geologic setting, improper section shape of the tunnel, wrong practice of NATM construction, etc.
裂缝产生的原因主要是早期收敛变形，地质条件复杂多变，隧洞断面形状不当，新奥法施工运用欠妥等。
The relation between the deformation shape of casing and the areas and subjected to ground stress and the theory solution of non-uniform in-situ stress were analyzed.
对套管的变形形态与地应力作用大小、应力范围之间的关系和非均匀地应力的求解进行了研究。
The challenging problems in shape deformation are preserving geometric details and preventing unnatural volume changes as much as possible while satisfying the user constraints.
三角网格模型的变形除应实现用户指定的形状变化外，还应尽量保持模型原有的几何细节，防止不合理的体积变化。
The results showed that serious boiler scale caused long term overheat and creep of boiler plates which resulted in the drum shape deformation of cylindrical body of boiler.
结果表明，锅炉严重结垢使得锅筒底部钢板长期过热产生蠕变，从而导致锅炉锅筒产生鼓包变形。
With the decrease of the height-width ratio, the amount of horizontal displacement and flexural deformation of the wall reduces and the shape of the wall back changes in turn.
随着高宽比的减小，挡墙的水平位移量和挠曲变形逐渐减小，墙背变形形态亦发生了变化；
With the decrease of the height-width ratio, the amount of horizontal displacement and flexural deformation of the wall reduces and the shape of the wall back changes in turn.
随着高宽比的减小，挡墙的水平位移量和挠曲变形逐渐减小，墙背变形形态亦发生了变化；
应用推荐