Methods: we obtained the relationship between RBC deformation index and RBC membrane viscosity in the process of RBC deformation recovery.
方法：利用红细胞变形恢复过程，建立红细胞变形指数与红细胞膜粘度的关系。
Nylon is predominantly used past the useful pressure range of TFE because of its ability to resist permanent deformation (or creep), and recovery after load.
在TFE有效压力范围内，尼龙以前被广泛的使用，因为尼龙具有抗永久性变形(或蠕变)的能力，并且在负载后能够自行恢复。
Its transient recovery rate of deformation, complete recovery time of deformation and maximal compressive strength were determined with biomechanical approach.
用生物力学测定仪测定其不同压缩比率下的瞬时形变恢复率、最大形变恢复率及最大极限压缩强度。
After deformation and heat treatment, single crystal al wire will generate a mass of dislocation cells, high density dislocations and evident recovery phenomena.
单晶铝线材在变形和加热后会产生大量的位错胞、高密度位错和明显的回复再结晶现象。
Dynamic recovery and recrystallization of the composite generate with the increasing of deformation temperature.
随变形温度升高，复合材料发生动态回复再结晶。
The initial large grain microstructure became much finer after superplastic deformation. The large grained superplastic phenomenon could be explained by continuous recovery and recrystallization.
在超塑性变形过程中发生发生连续回复和再结晶，导致原始大晶粒组织经超塑性变形后的显著细化。
The influences of such factors as PA6 content and polymerization degree, deformation stretch and recovery temperature, recovery times on the shape memory function were studied.
研究了PA6含量与聚合度、形变拉伸温度与形变回复温度及回复次数等因素对形状记忆功能的影响。
The pad body can be deformed repeatedly and has high deformation recovery speed, thus effectively reducing the impact on the nose bridge by the glass frame during walking, running and jumping.
由于托体可以反复形变，而且形变恢复速度快，故可以有效减少走路、跑步和跳跃时眼镜架对鼻梁的冲击。
During deformation, because of dynamic recovery and recrystallization, a turning point appears on the curve of true stress with temperature and strain rate.
这个折点的出现可能与变形过程中的动态回复与再结晶有关。
The principle of the internal faults (cavities and cracks originated from inclusion) recovery was investigated in the plastic deformation by using the method of physical modeling at high temperature.
论文采用钢试件高温模拟方法对热加工过程中易引起大型锻件内部探伤超标的孔洞型缺陷、夹杂性裂纹等缺陷的修复规律进行了探讨。
How to control the slope deformation and stability became the key technical issue in the safe recovery of the hang-up wall ore.
如何控制边坡的变形与稳定构成了挂帮矿安全回收的关键技术问题。
This technology keeps the casing in an elastic state in the whole thermal recovery process without plastic deformation taking place, and thus resolves the problem of thermal casing failure.
该技术可使套管在整个开采过程中一直处于弹性状态，不发生塑性变形，从而解决了套管热破坏问题。
A method of energy difference between elastic deformation and elastic-recovery deformation is developed to determine the residual deformation energy.
本文提出用弹性变形能与弹复变形能的差值来确定残留变形能的方法。
It was found that polymer with higher hydrophobic group content had stronger recovery after deformation in three kinds of polymers with the same shear viscosity.
实验发现在相同剪切粘度下的三种聚合物，形变恢复能力随着疏水基含量的增大而增大。
The recovery after deformation was proposed to characterize the elastic property of polymer solution.
提出用形变恢复能力来表征聚合物溶液弹性的大小。
From the results of the experiments, a conclusion can be acquired. In terms of J55, its dynamic tensile strain-stress curve is a typical deformation - recovery curve of the rheological metal.
结果证明：对于J55钢，在这一温度范围内的动态拉伸应力-应变曲线，是典型的流变金属的形变-回复曲线。
In addition, there is a certain recovery of deformation for pile body and anchor steel under the forward tension condition after unloading.
另外，卸载后，在正的受拉状态下，对于桩体和锚杆钢筋，变形均有一定程度的恢复。
Theelastic contact deformation between work roll and work-piece, work-piece deformation near the edge of plate and elastic recovery are discussed.
对板带轧制过程中轧辊与轧件的接触变形进行了分析，得到了轧辊弹性压扁、轧件边部减薄以及轧件弹复的分布规律。
Theelastic contact deformation between work roll and work-piece, work-piece deformation near the edge of plate and elastic recovery are discussed.
对板带轧制过程中轧辊与轧件的接触变形进行了分析，得到了轧辊弹性压扁、轧件边部减薄以及轧件弹复的分布规律。
应用推荐