Design a variety of radial clearance and the contact Angle, to meet different application requirements of load and deflection.
设计有多种径向游隙和接触角，满足不同的应用负荷和偏斜要求。
This paper studied the relationship among bending moment, curve, deflection and concrete compression height by design principle for reinforced concrete structure.
从钢筋混凝土结构设计原理出发，分析截面弯矩、曲率、挠度、受压区高度之间的相互关系；
With the promotion of road grading, the control of vertical deflection in bridge design is becoming more important.
随着道路等级的提高，桥梁设计中竖向挠度的控制显得尤为重要。
This paper describes the design method of deflection crank slider mechanism of the given stroke velocity rate and slider stroke, which has optimum transmission performance.
探讨了给定行程速比及滑块行程的偏置式曲柄滑块机构具有最佳传动性能的设计方法。
This paper puts forth the calculating formula of the deflection caused by shear distortion, which has a reference value to the design of the main shaft of the machine tool.
本文给出了考虑剪切变形引起的挠度计算公式，对现代机床的主轴设计具有一定的指导意义。
After that, the calculation method about double pre-stressed composite structure's bearing capability and deflection are investigated, which provide the consults to future research and design works.
另外通过与常规预应力结构的比较，研究了二次预应力组合结构正截面承载能力和结构变形的计算方法，为今后的设计和研究提供了参考。
The optimal design of minimax deflection of an annular plate is studied in this paper.
本文讨论环形板的最大挠度极小化的优化设计。
Deflection control of support system under wind load is one of the main problems for the design of point-supported curtain wall.
风荷载作用下点支幕墙支撑体系的挠度控制是幕墙设计中的主要问题之一。
In the paper, the design of deflection winding configuration is described.
本文介绍了偏转绕组结构的设计。
The structural properties of concrete bridge externally prestressed with CFCC, and the analysis methods of deflection, ductility, bending and shear design of the bridge are discussed.
探讨了碳绞线体外预应力混凝土桥梁的结构特点和构造措施，以及该类桥梁中挠度、延性及抗弯、抗剪的计算分析方法。
This method may possibly be used to estimate influence of high order harmonic field on hysteresis loss to optimize the design of deflection yoke ring and to develop energy saving ferrite materials.
该方法适用于估测高次谐波场对磁滞损耗的影响，降低能量损耗的偏转系统磁芯结构的优化，磁性材料的选择等。
Therefore, seeking optimal deflection Angle has become a critical problem for the design of turbine and the control of deflection Angle.
因此，寻求最优的偏角规律成为水轮机设计和偏角控制的关键问题。
In order to evaluate the truss design and construction quality correctly, the deflection calculation methods using three different datum selections are introduced.
基准选取对网架结构挠度计算影响很大，为了更好的评价网架的设计及施工质量，本文介绍三种不同基准选取方法计算检测挠度。
Simulate the avalanche circuit in series with PSPICE module, design the high voltage short plus generation circuit by avalanche transistor in series for the sweep deflection circuit of streak camera.
运用PSPICE模型对串联雪崩电路进行了仿真，设计出了用雪崩三极管串联的高压短脉冲产生电路，该电路可以用于条纹相机中的扫描电路。
In addition, the advantage of FWD deflection bowel and FWD application in pavement design and evaluation are illustrated by examples.
并列举了应用FWD测量路表弯沉盆的优点及FWD在道路设计与评价中的一些基本用途。
The result show that: under the design load the maximum deflection and stress is less than code values, the bridge is safety.
计算结果表明：该桥在设计荷载下的最大挠度值及应力值均小于规范规定值，结构处于安全的范围内。
An observation design criterion which ensures the observation precision of the vertical deflection is presented.
提出了保证垂线偏差测定精度的观测设计准则。
Authors design the maintenance processes, compile the operation schedule by Gantt chart and network diagram and analyze the schedule by deflection analysis method.
作者对检修过程进行流程设计，提出利用甘特图、网络图编制进度安排，利用偏差分析法对进度进行分析。
The formulas calculating deflection and ultimate bearing capacity can offer the design basis for the application of the composite board in projects.
本文提出的挠度与极限强度计算式对该复合板在工程中的推广应用提供了设计依据。
Based on analyzing the relations of degree of pre-stress to stress, deflection and crack of concrete beam, a design method is pro-posed.
在详细分析了预应力度同梁的应力、位移、开裂的关系的基础上提出了部分预应力混凝土梁的设计方法。
Puts forward the method and principle to adjust the deflection of conveyer belt automatically and carries out the introduction design to the mechanical gearing design of automatic system to a...
提出了带式输送机自动调偏的方法和原理，对自动调偏系统的机械传动装置进行了初步设计。
Presser foot of automatic deflection Angle positioning design, ease and fast in collection and placement.
压脚的自动偏摆角度定位设计，鞋子取放容易，快捷。
The inlet flow angle and diviation angle were confirmed which was applied to low cascade experiment result of American NACA, and controlled diffuser factor and flow deflection angle in design.
并应用美国NACA低速叶栅试验结果确定流入角和落后角，设计中控制扩散因子和气流折转角。
This method was used on the Maogang River Bridge construction, resulting in a final deflection differing by 2cm from the design value.
泖港大桥应用此法进行控制，其最终挠度与设计值仅差2厘米。
In this paper, computer aided design of the multi-magnetic-pole deflection system, including three stages with 20 pole pieces, was developed. Our results showed that the deflection...
对三段式的二十极多磁极偏转系统的计算机辅助设计方法进行了介绍，得到会聚良好、具有较高偏转灵敏度的多磁极偏转系统。
The numerical experiments show that the high order polynomial analytic method can quickly, efficiently and reliably design high performance supersonic large deflection Angle preliminary profiles.
数值模拟实例表明，高次多项式解析造型方法能快速、高效、可靠地设计出高性能的超音速大转折初始叶型。
Different deflection direction can be obtained through the different structure design.
通过不同的结构设计可以控制驱动膜片结构的弯曲变形方向。
Structural type, design and calculation method of cellular voided flat slab with plastic boxes embedded in a underground garage were presented, calculating method of the deflection was proposed.
结合已建成的工程实例介绍了使用薄壁塑料盒作为填充体的蜂窝式空心无梁楼盖的结构型式及其设计计算方法，并提出了该类空心无梁楼盖板的挠度计算方法。
Structural type, design and calculation method of cellular voided flat slab with plastic boxes embedded in a underground garage were presented, calculating method of the deflection was proposed.
结合已建成的工程实例介绍了使用薄壁塑料盒作为填充体的蜂窝式空心无梁楼盖的结构型式及其设计计算方法，并提出了该类空心无梁楼盖板的挠度计算方法。
应用推荐