The theory and the formula of the deflection deformation survey with total station instrument were introduced, and the survey accuracy was analyzed.
论文介绍了全站仪法测量桥梁挠度的原理和计算公式，并对全站仪法观测桥梁挠度变形值的测量精度进行了分析。
The vertical construction which can avoid deflection deformation is used. Data auto-sampling device is used in the measurement, so the sampling position is accurate and the sampling speed is high.
该测量仪采用立式回转轴结构，优点是避免产生挠度变形，提高了测量精度，该仪器采用数据自动采集装置，采样位置准确，速度快。
Rotational deformation of the shaft will produce maximum deflection.
转动的泵轴会弯曲变形，产生最大挠度。
The paper has studied straightening stress and residual deformation of circular shaft by using elastic - plastic theory, deueloped calculation formula of straightening loud in given deflection error.
从弹塑性理论出发以圆截面轴为例对校正应力与残余变形进行了分析研究，提出了在给定弯曲误差下的校正载荷的计算公式。
The damage factor is too high, the compressed air blowing pipe deflection, flower plate deformation and other factors, can be adjusted to prevent breakage.
破损因素是压缩空气过高、喷吹管歪斜、花板变形等因素构成，调整后即可防止破损。
The analysis of free vibration of hydropower house by means of two methods are deformation of inclination Angle and slope deflection.
本文首先叙述用两种方法(倾角变位法和角变位移法)分析水电站厂房的自振特性。
This paper deals with the inner force and deformation of curtain wall glass caused by vertical and side forces by using nonlinear theory of large deflection.
探讨了幕墙玻璃在纵力和侧力的共同作用下的内力和变形根据实际的变形状态运用大挠度的非线性理论。
This makes it possible to analyze the effect on gear mesh of such factors as gear box deformation, axial end loading and axial deflection, etc.
用这种方法可以分析多种外界因素对齿轮啮合的影响，如箱体变形、轴端受力、轴线挠曲等；
The delayed elastic deformation stage came later, the bend deflection increased more quickly, and breaking life shortened with the increase of the prolongation of the maximum load hold time.
随着最大载荷保持时间的增加，塑木复合材料进入延迟弹性变形阶段越晚，弯曲挠度增加越快，断裂寿命降低。
The deflection and deformation of slender column and eccentrically loaded column of ultro-high strength concrete filled steel tubes under loading were studied.
对钢管超高强混凝土长柱、偏压柱在荷载作用下的挠度及变形特点进行了研究。
Basing on the elastic bending theory of beams in large deflection, the non-linear shearing behavior of cellular materials under large deformation is studied in the paper.
将梁的弹性大挠度弯曲理论应用于蜂窝壁板，研究了大变形条件下蜂窝材料的非线性剪切变形行为。
The tooth deformation includes the contact deformation, deflection, base deformation and the influence of the body deformation, and the contact stress and the stress distribution are computed too.
轮齿变形包括轮齿接触、挠曲、基础变形和齿轮本体变形的对它影响，还有接触应力和分布。
The fundamental formula of large deformation, when the deflection is of the same order as the length of the shell, is derived exactly for cylindrical shell under cylindrical deformation.
当薄壳为柱形且作柱状弯曲时，精确地求得了壳的挠度与长度同级的大变形基本公式。
What are the approximate foundation loads? Are there deformation or deflection limitations beyond the usual requirements?
什么是近似基金会负荷？有变形或挠度极限超过平常的要求吗？
A method of calculating elastic curve for semiflexible plate wind tunnel nozzle has been presented, based on the linear theory of small deflection of beam deformation, in this paper.
本文基于梁弯曲变形的小挠度线性理论，提出了半挠性喷管挠性板弹性曲线的计算方法。
The fundamental formula of large deformation, when the deflection is of the same order as the thickness of the shell, is derived based on rational simplification.
经过合理的简化，给出了壳的挠度与厚度同级的大变形基本公式。
Large deformation problems of Euler beams are studied. An efficient integration formula for the deflection is deduced directly from the nonlinear differential equation.
对欧拉梁的大变形问题进行了深入研究，直接从欧拉梁的非线性挠曲线微分方程，推导出求解梁挠度的一种简便有效的积分表达式。
The deflection value can increase 44.7% when considering shear deformation. So shear deformation can not be ignored in the actual design.
考虑剪切变形能增大44.7%的挠度值，因此在实际中不可忽略。
The deformation of frame-tube structure under the lateral load is constituted by both shear and bend deflections. The effect of shear lag must be considered for the bend deflection.
框筒结构在水平荷载作用下的变形由剪切变形和弯曲变形两部分组成，弯曲变形必须考虑正、负剪力滞的影响。
Aimed at the bend of poplar-straw laminated beam, the theory of delamination shearing deformation was used to analyse its bending deflection and strength, and compared the results with other theories.
针对杨木—秸秆层合梁的弯曲问题，利用分层剪切理论对其变形和强度进行了分析。并将分析结果与经典理论、一阶和高阶剪切变形理论的结果进行了比较。
The large deflection buckling deformation of cold rolled strip acted on by residual stress is studied by using 3-Power spline function energy method.
采用三次样条函数能量法，对冷轧轧后带材在纵向残余应力作用下的大挠度屈曲变形和临界失稳问题进行了研究。
The abnormal deformation or local damage of steel structure can be reflected by the load-deflection curve and the deflection curve of the longitudinal axis.
钢结构的异常变形或局部损坏可通过荷载—挠度曲线以及纵轴线的挠度曲线反映出来。
This paper analyzes the influence on the pivot point and deflection angle from the pendulum shaft's deformation in course of the test.
本文分析了试验过程中摆杆形变对柔性接头摆心、摆角数据的影响。
The test result shows that deflection of CFST truss girder is mainly attributed to deformation of shear-bending parts and much smaller than that of solid web girder.
试验结果表明：钢管混凝土桁梁变形比实腹梁小很多且主要集中于边段；
After fetching each deflection equations, the situation of deformation and internal forces can be achieved.
有了各段的挠曲方程的解以后，可以用求导的方法求出双排桩各点的变形及内力情况。
The results showed that shooting method was effective to deal with the deformation of elastic-plastic beam with large-deflection.
结果表明，打靶法是解决弹塑性梁大挠度变形问题的有效方法。
By the deflection test, the deflection produced by the deformation of joint field can be gained, accordingly, the change in the included Angle that the beam axis relative tot...
通过挠度测试，可以求出因节点域变形导致梁发生转动而产生的挠度值，进而可以得到梁柱夹角发生的改变量。
The deck pavement can effectively improve the deformation properties, one hand is to reduce girder deflection, to make the deflection distribution more uniform and the deflection change curve gently.
桥面铺装能有效改善桥梁的变形形状，一方面减小主梁挠度，使得挠度分布更加均匀，挠度变化曲线平缓。
The deck pavement can effectively improve the deformation properties, one hand is to reduce girder deflection, to make the deflection distribution more uniform and the deflection change curve gently.
桥面铺装能有效改善桥梁的变形形状，一方面减小主梁挠度，使得挠度分布更加均匀，挠度变化曲线平缓。
应用推荐