Pressure relief devices are integral parts of the cylinder valves.
它们是钢瓶阀门整体的一个组成部分。
WARNING: Improper use of cylinder valves may result in serious injury!
警告：不正确使用钢瓶阀门会导致严重伤害！
Open cylinder valves slowly and carefully after the cylinder has been connected to the process.
在钢瓶已经连接到过程后，慢慢地仔细地开启钢瓶阀门。
Like all cylinder valves, optimum performance requires knowledgeable operators and appropriate procedures.
象所有的钢瓶阀门一样，最佳的表现需要有知识的操作员和合适的程序。
This paper analyses the specification and type testing of cylinder valves for non-refillable cylinders at home and abroad.
对非重复充装瓶阀的技术要求和型式试验采用的国家标准和欧洲标准进行了比较分析。
A working knowledge of cylinder valves can improve processes, save time and money, prevent problems, and improve the safety of your operation.
钢瓶阀门的应用知识能够改善工艺、节约时间和金钱、预防问题和改进你的操作的安全性。
The specification of compressed natural gas cylinder valves for vehicles at home and abroad were analysed and some suggestion were put forward.
对车用压缩天然气瓶阀的技术要求进行了国内外的比较分析，并提出了合理的建议。
Recommended Closing Procedure: Close the cylinder valve tightly using a gloved hand. Always wearing gloves when operating cylinder valves. NEVER use wrenches or other persuaders to operate the valve.
推荐的关闭程序：用戴手套的手紧紧地关闭阀门。推荐操作钢瓶阀门时总是戴手套。禁止用扳手或其它强制性的工具来操作阀门。
The SOHC KA24E was replaced by a new DOHC KA24DE now with 4 valves per cylinder, producing 15 more ponies HP, for a total output of 155 HP (116 kW).
SOHC KA24E型发动机升级成了DOHCKA24DE型，每气缸4气门，输出增加了15马力，达到了155马力(116千瓦)。
The most common "hole" in a cylinder occurs where the top of the cylinder (holding the valves and spark plug and also known as the cylinder head) attaches to the cylinder itself.
气缸上的孔最可能出现在气缸顶部（装阀门和火花塞的部位也即气缸盖）。
Comments: When working with these valves it is very important to use good cylinder change out procedures.
评论：当与这些阀门一起工作时，使用良好的钢瓶更换程序是非常重要的。
Expound working principle of extraction check valves and the calculation methods of the cylinder design.
阐述了抽气止回阀的工作原理及气缸的设计计算方法。
In order to prevent misuse, and some special valves and the cylinder using a special connection between the mouth.
为了防止误用，有些专用减压阀与钢瓶之间采用特殊连接口。
Specification matching calculations are made for the main hydraulic components such as the main pump, valves and oil cylinder and some main static specifications in the system are also calculated.
对液压部分进行了主要元件如主泵、阀和液压缸的主要参数进行了匹配计算，并对系统的一些主要静态指标进行了计算。
The cylinder head carries the valves, valve springs and the rockers on the rocker shaft, this part of the valve gear being worked by push-rods.
缸盖上装有气门、气门弹簧和摇臂轴上的摇臂，推杆推动这部分气门传动机构工作。
The start is performed by direct injection of air into the cylinders through the starting air valves in the cylinder heads.
这个启动，是由直接注射空气进入气缸，通过在气缸正面的启动空气阀完成的。
Secure the cylinder head on a level surface which allows easy access to the valves from underneath.
将气缸盖固定在水平面上，这便于从下方接触气门。
VRP120 single acting pilot check valves lock a single acting cylinder.
VRP120型液控单向阀用于锁紧单作用液压缸。
Valves in modern car engines are located in the cylinder head at the top of the engine.
现代汽车发动机里的阀门位于发动机顶上的汽缸盖。
Mud valves and Angle by the hydraulic cylinder type combination valve, hydraulic power drive cylinder valve lift, the valve open or closed channel, in order to achieve the fluid off.
排泥阀产品由液压缸和角式截止阀组合而成，液压缸内动力带动瓣升降，使阀体通道开或闭，以达到流体通断。
Hence, the ME engine features fully integrated control of all functions like the governor, start and reversing, fuel, exhaust and starting valves, as well as cylinder oil feeding.
因此，ME系列柴油机的特点是调速、起动、换向、供油、排气阀和起动阀，以及气缸油的注油控制等所有功能集为一体。
The rotating valve is connected with pressure cylinder which is connected with four shut off valves through one hydraulic lock.
转阀通过一个液压锁与增压缸相连。增压缸与四个闭锁阀相连。
The sensors are attached to the existing indicator valves and they all measuring the cylinder pressure at the same time.
所有的传感器都链接到示功阀上，同时测量各个气缸的压力。
Our main products cover actuating element (cylinder), pneumatic component (valves), air source processing unit, air hose, auxiliary components and integrated system.
公司主要产品有：执行元件(气缸)、气动控制元件(阀)、气源处理元件、空气软管、辅助元件以及成套系统。
Hydraulic seals, pneumatic seals, solenoid valves, booster oil cylinder are used the well-known foreign brand products including parts of native brands.
液压密封件、气动密封件、电磁阀、增压缸等都选用国外知名品牌产品、部分选用国内品牌。
Hydraulic seals, pneumatic seals, solenoid valves, booster oil cylinder are used the well-known foreign brand products including parts of native brands.
液压密封件、气动密封件、电磁阀、增压缸等都选用国外知名品牌产品、部分选用国内品牌。
应用推荐