And its critical cutting thickness and hardness of the material relevant.
而其临界切削厚度与材料的硬度有关。
The cutting thickness is regulated by accurate ball screw rod which ensures localized precision.
锯切厚度由精确的滚珠丝抗控制，确保定位精度。
The effects of different cutting thickness on surface quality and slice quality are studied in this paper.
研究了不同切削厚度对竹材表面质量与屑片质量的影响。
Factors like internode, node, cutting thickness, moisture content, cutting speed could influence the cutting force in varying degree.
竹材的节间、节部、切削厚度、含水率及切削速度等因素对切削阻力均有不同程度的影响。
Simplifying the adjusting processes of the veneer rotary cutting thickness is the key of realizing the automation of veneer production.
简化单板旋切厚度的调节过程，是实现单板旋切加工自动化的关键。
The effects of cutting parameters, the tool rake Angle, cutting thickness and speed, for bamboo on cutting forces are studied on this paper.
研究了竹材切削不同刀具前角、切削量与切削速度对切削力的影响。
Adjusting thickness-cutting knob may carry out stepless speed regulation of push rod so as to meet the requirement of different cutting thickness.
调整厚度切割旋钮，可对推杆进行无级调速以满足不同切割厚度的要求。
The variation rules of critical cutting thickness on the different crystal and different orientation of KDP crystal are obtained by theoretic calculate.
通过理论计算得到了KDP晶体在不同晶向上临界切削厚度的变化规律。
Set up appropriate processing parameters in accordance with cutting thickness and material to be propitious to improve processing efficiency and surface quality.
根据切割厚度和材质设置适合的加工参数，以利于提高加工效率和表面质量。
The mechanism, features and difficult problems in superfine machining are analyzed. The relationship between the minimum cutting thickness and the circular radius is confirmed.
分析了超微细切削加工的机理、特点及技术难点，并对最小切削厚度与刀具刃口圆弧半径的关系进行了量化分析。
In addition, they believe, for tapping there exists a critical cutting thickness (thread depth) value of the critical cutting thickness within the tapping can reduce the tapping torque.
此外，他们认为，对于攻丝存在一个临界切削厚度(螺纹深度)值，在临界切削厚度的范围内，攻丝能降低攻丝扭矩。
It is a sign of the machining level of ultra-precision cutting reflected by the achieving of minimum cutting thickness. And it will be significant to the analysis of extra thin cutting.
最小切削厚度的获得是反映超精密切削加工水平的重要标志，因此对极薄切削进行分析具有重要意义。
But the argon plasma arc voltage, low enthalpy is not high, cutting ability is limited, and cut the air than the thickness of the cut about 25% lower.
但氩气等离子弧的电压较低，焓值不高，切割能力有限，与空气切割相比其切割的厚度大约会降低25%。
Cutting current is adjustable to adapt to the various thickness of sheet metal processing.
切割电流可调，能适应各种厚度板材的加工。
The relationships between the cutting speed and a incised workpiece of intension, thickness are analyzed.
通过试验，分析了被切割工件强度和厚度与切割速度之间的关系。
So it can cut different thickness scrap steel. Its cutting route is very long in horizontal and vertical direction.
本机采用变频调速，调速范围宽，能切割不同厚度的废钢，水平、垂直方向切割行程大。
In cutting experiments, it can be observed and measured that the chip thickness, the tool wear, the screw thread teeth, and so on.
在切削实验中，可对切屑厚度、刀具磨损及螺纹等的形貌进行观察并测量其尺寸。
So in before cutting the thickness of the material according to the correct choice of cutting current and the corresponding nozzle.
所以在切割前要根据材料的厚度正确选用切割电流和相应的喷嘴。
Be able to understand the cutting clearance with different die, and calculate the cutting clearance with the different thickness of the material.
能理解不同模具的切刀间隙，并根据不同的材料厚度计算出切刀间隙。
Rotary cutting it to the chip or equal to the width of the linear cutting chip thickness.
它等于旋削中的切屑宽度或者等于线性切削中的切屑的厚度。
Thickness of cornea and corneal flap were measured and calculated before and after laser cutting.
激光切削前后对角膜进行测厚，计算角膜瓣厚度。
Automatically control the cutting speed to avoid over-burning according to plate thickness. Possible to edge cutting, offset cutting, to avoid wasting of meal sheet caused by calculation errors.
根据钢板厚度，在转角处可自动限速，有效防止过烧。支持边缘切割、偏移切割，对较厚的钢板可减少预热时间，并可避免因排料计算错误而造成的板材浪费。
This machine is used for cutting clay-slug into standard size green bricks with equal thickness.
本机用于将切条机输送来的坯条，切成厚度相同的标准砖坯。
This article has made scientific researches on the optimum of process for veneer rotatory-cutting, and obtained the optimum technologies for two kinds of veneer thickness of linden.
本文在单板旋切工艺最优化方面进行了研究得出椴木两种单板厚度的最佳工艺条件。
When propane gas cutting low carbon steel plate, the cost varies with the thickness of the steel plate.
用于低碳钢板气割时，气割成本随板厚不同而变化。
Cutting speed is related to the thickness and hardness of materials to be cut.
切割速度是与所需切割的材料厚度及材质的硬度相关联的。
With the hydraulic control system its cutting speed can be adjusted easily by the size and the thickness of the caliber.
它采用液压进给，进给量切削速度可根据口径大小、臂厚随意调整。
With the hydraulic control system its cutting speed can be adjusted easily by the size and the thickness of the caliber.
它采用液压进给，进给量切削速度可根据口径大小、臂厚随意调整。
应用推荐