Bite type fitting consists of three parts: body, cutting ring and nut.
卡套式管接头由三部分组成：接头体、卡套、螺母。
Adopted with rigid and wearable alloy materials, the glass-like plate and cutting ring have longer longevity.
眼镜板和切割环采用高硬耐磨合金材料，寿命更长。
The wearing parts, such as the anti-wearing plate and the cutting ring , have a long service life up to 30000 m3 under favorable condition .
眼镜板、切割环等磨损件，经过不断的技术攻关，使用寿命长，最佳泵送状态时，其寿命可达3万方。
The super anti-weary glass plates and cutting rings made of hard alloy greatly prolonged the service life the weary parts. cutting ring with self-compensating wear-resisting ring.
—眼镜板和耐磨环采用硬质合金，耐磨性好，且更换方便，耐磨环具有磨损后自动补偿间隙功能。
The distribution law of pressure potential in saturated soil using two-ring infiltration method to determine the permeability coefficient was different to that using cutting ring method.
当采用双环入渗法和环刀法测定土壤的饱和渗透系数时，土壤剖面土壤水压力势分布规律不同。
If the cutting ring and eye wear plate is not serious, cutting ring and the eye plate spacing <0.1mm, and no more than 1mm between them in a trench scratches, water law can be used directly.
若切割环和眼睛板磨损不严重，切割环和眼睛板间距＜0.1mm，且它们之间无超过1mm的沟槽划痕，可用直接打水法。
To improve efficiency and veracity of soil sampling in testing bulk density, the cutting ring method and in situ soil tube method were combined and a multi-segment in situ soil sampler was designed.
为了提高土壤容重测定中土样采集的效率和精准性，将环刀法和原状取土管法结合，进行了分段式原状取土器的研制。
Given this, it is necessary to detect the roadbed compactness with Rayleigh wave method and compare it with the sand cone method and cutting ring method, which verify its feasibility and reliability.
鉴于瑞雷波勘测技术在工程领域中的应用范围逐渐扩大，并取得了较好的效果，故有必要以瑞雷面波法对路基压实度进行检测，并与常规方法灌沙法和环刀法进行对比，验证其可行性与可靠性。
Then, on May 4th, tens of thousands formed a human chain around both sides of the 27km (17-mile) ring road, surrounding and cutting off the capital.
随后，5月4日数万人组成长约27公里的人链，将首都包围并切断其与外界的联系。
The Statistical analysis of piston ring tracer cutting errors shows that there is a systematic error in the tracer cutting.
对活塞环仿形车削误差的统计分析表明：靠模仿形加工中存在系统误差。
And give out the unified optical path, Newton's ring radius and convex lens curvature radius measurement formula of non - contact type, simple cutting type and tangent type Newton's Rring.
并给出了非接触式、浅近切割式及相切式牛顿环的统一的光程差，牛顿环半径及凸透镜曲率半径测量公式。
This paper describes basic structures and working principle for the machine for cutting and expanding the wheel lock ring, showing the design concept about essential elements.
介绍挡锁圈扩切机基本结构及工作原理；机床的几个关键部位的设计构思。
This paper introduces a new method cutting the profile of tooth of large gear ring, which has no upper limit diameter.
介绍了一种大型齿圈齿形加工的新方法，并对其加工原理、主要参数的选择计算和切削试验结果进行了分析。
Theory derivation proved that non-contact type and simple type cutting Newton's Ring device possesses the identical interference law and measurement …
并给出了非接触式、浅近切割式及相切式牛顿环的统一的光程差，牛顿环半径及凸透镜曲率半径测量公式。
Cracked tungsten tubes prepared by chemical vapor deposition were investigated by ring machine cutting method and X? Ray stress analysis system.
采用切环测量法及X射线应力分析方法对化学气相沉积制备的开裂钨管进行测量与分析。
We analyse the influence of the elastic deformation and the surface roughness for lubricating characteristics and give a thought of cutting groove in piston ring.
分析了弹性变形、表面粗糙度对润滑性能的影响，并提出了开槽环的设想。
A primary analysis for cutting force of the tools and the frictional force in rotating seal ring are also given.
切削刀具的切削力及密封圈回转摩擦力的初步分析计算。
The structure and principle of two new types of cutting tools (bevel wedge type and eccentric type) for boring O-ring grooves have been introduced in this paper.
本文介绍了斜楔式和偏心式两种新型内孔挖槽刀具的结构和原理。
The zero stress state of an artery is brought by cutting a ring of the artery radically and, then, the ring segment springs open into a sector.
研究了一个新的动脉壁零应力状态测量方法和动脉壁应变分析方法。
Masterfully set diamonds stand alongside conceptual designs that reflect a cutting-edge approach, such as Etienne Perret's ring made for two fingers.
巧妙地设置钻石，反映了尖端的概念上的设计方法，如艾蒂安贝瑞完全适用两个手指的戒指。
Analyses hydraulic system of cutting unit of roadheader-ring MLE250/500-M and the electro-hydraulic control technology was adopted, it may obtain higher speed of roadheader-ring in mining face.
分析了MLE250/500-M型掘锚机截割机构的液压系统，提出采用电液控制技术方案，从而达到快速掘进的目的。
Analyses hydraulic system of cutting unit of roadheader-ring MLE250/500-M and the electro-hydraulic control technology was adopted, it may obtain higher speed of roadheader-ring in mining face.
分析了MLE250/500-M型掘锚机截割机构的液压系统，提出采用电液控制技术方案，从而达到快速掘进的目的。
应用推荐