An experiment on material removal amount with the cutting distance and shape of passage is described.
介绍了用于研究材料去除量与加工距离和形状关系的实验。
The synchronous lifting mechanism has a stable structure and simple operation, can reduce the complexity of a control system, effectively control the cutting distance and has low cost;
本发明结构稳定、操作简便、能降低控制系统的复杂性、有效控制切割距离且成本较低；
An edge cutter (3) is arranged on the seat frame (4) of the air extruding roller. The constant cutting distance improves and ensures the quality of a cutting edge after the rolls are combined.
切边刀(3)安装在挤气滚筒座架(4)上，恒定的切刀距离，提高和保证了合卷后切边的质量。
According to Roberts, Friedman delivered a brief, cutting critique — probably in the same nasal monotone I remember when, decades later, he returned my long-distance calls collect.
按照罗伯茨的说法，弗里德曼用充满鼻音的单调语气发表了简短而尖刻的评语，这种语调恐怕与他数十年后回复我拨打的对方付费长途电话时的语调一模一样。
This energy release imbalance, closely related with many process parameters, such as plasma arc compression degree, cutting speed and nozzle to the distance, etc.
这个能量释放的不平衡，与很多工艺参数密切相关，如等离子弧压缩程度、切割速度及喷嘴到工件的距离等。
If he went further—speeding parole hearings for the 2,400 or so who have completed their tariff—he would be some distance towards his department's goal of cutting 3,000 prison places.
如果他能更进一步地加快假释听证会对大约2400名已服刑完毕的犯人的审判，他可能就离司法部门要削减3000个监狱席位的目标不远了。
A get-back path is planned based on the bionic principle, saving time and cutting down the distance needed to back.
本文还提出一种基于仿生原理的回程方式，使机器人在回程中节省了时间和距离。
When sawing to control a number of sawing, avoid scratch, and a waste material and light fabric cutting, each with a clean cloth to stop the distance between.
锯切时要控制一次锯切支数，避免擦花，并且关于废品坯料和光面料锯切时，要每支之间用洁净布料停止距离。
Based on hardware-accelerated texture-based volume rendering algorithm, this paper proposed two methods for volume cutting, which are based on either depth buffer or discrete distance field.
在硬件纹理加速体重建算法的基础上，提出了两种模拟三维数据切割的方法：利用深度缓存实现和利用离散距离场实现。
Five, the nozzle height: refers to the nozzle surface and cutting the distance from the end, it constitutes the part of the whole arc long.
喷嘴高度：指喷嘴端面与切割表面的距离，它构成了整个弧长的一部分。
Finally, space parameter measurement method based on feature point selection was designed to accurately measure the distance, Angle and volume of cutting motor structure.
最后，设计出基于特征点拾取的空间参数测量方法，实现剖切后发动机结构空间距离、角度和体积的精确测量。
The maximum cutting stress lie of the radial distance of 0.5 double diameter nozzle, while the maximum pull stress lie in the surface edge of the rock.
岩石破坏时最大剪应力位于0.5倍喷嘴直径的径向距离处，同时在固体介质表面边缘产生最大拉应力。
Then, based on the principle of not losing money in mining, the optimal cutting rock height and stoping distance for extracting lying side triangular ore pillar are optimized.
基于不亏本原则，确定回采下盘三角矿体的最合理切岩高度和后退距离。
The microhardness of various point of milling working surface gradually reduces with the increase of distance of cutting surface, and then remains flat.
垂直于铣削加工面各点的显微硬度，随着距切削表面距离的增大而逐渐降低，且趋于平缓；
Suggestions about distance between curtains for cutting off water and protecting piles and about protective measure of soil …
给出了止水帷幕与支护桩之间的距离及桩间土保护措施的建议。
An experiment was conducted to investigate the effect of the distance between clamp and cutting notch for plywood bond strength.
通过试验，研究了胶合板胶合强度检测试验中夹具与试件槽口的距离对胶合板胶合强度的影响。
Torch height controller is used to adjust the distance between steel plate and cutting nozzle, in order to assure cutting quality and prolong the using of the cutting nozzle.
无论是火焰还是等离子切割，都必须保证割嘴离钢板的高度处于最佳的状态，从而得到最佳的切割效果和最长的割嘴使用寿命。
It introduces the programming method to cutting Revolving piston of equal distance plane on numerical control linear cutting machine by 3b format.
介绍了用3B格式在数控线切割机床上加工等距型面旋转活塞的编程方法。
Nowadays the art of seal cutting is very flourishing, but it is in a long distance from the modern life.
当代篆刻艺术空前繁荣，然而篆刻艺术与现代生活的远离，又无情地压缩了篆刻艺术的生存空间。
Using the experimental data, feature parameters of workpiece surface texture images were extracted. Relative distance was presented to evaluate the wear degree of cutting tools.
在实验数据的基础上，对工件表面纹理图像的特征参数进行提取，提出采用相对距离作为刀具磨损程度的评价指标。
Keep our feet at distance from the blades when starting the engine and the cutting assembly.
发动机和切割组合装置启动时，脚要远离刀片。
Compensation mode: during the cutting tool compensation cutter center track always deviated from the distance of a tool radius value programming track.
补偿模式：在金刚石刀具补偿进行期间，刀具中心轨迹始终偏离编程轨迹一个刀具半径值的距离。
Compensation mode: during the cutting tool compensation cutter center track always deviated from the distance of a tool radius value programming track.
补偿模式：在金刚石刀具补偿进行期间，刀具中心轨迹始终偏离编程轨迹一个刀具半径值的距离。
应用推荐