We offer cutting arc welding as well as post-processing tasks such as assembly, quality control packaging.
我们不仅提供适合切割、弧焊等制造工艺，还涵盖装配、质控、包装等后处理工序。
This study designed a system to generate ultrasonic-frequency pulsed plasma cutting arc, and experimentally investigated the vibration characteristics of the high frequency pulsed arc.
本研究设计了一种超声频脉冲等离子切割电弧发生系统，并通过实际切割试验，测试、分析了这种高频脉冲电弧的振动特性。
But the argon plasma arc voltage, low enthalpy is not high, cutting ability is limited, and cut the air than the thickness of the cut about 25% lower.
但氩气等离子弧的电压较低，焓值不高，切割能力有限，与空气切割相比其切割的厚度大约会降低25%。
When the current, voltage must be improved means that the improvement of arc enthalpy and cutting capability is improved.
当电流一定时，电压的提高意味着电弧焓值的提高和切割能力的提高。
So, choose as far as possible to improve the nozzle of small high cutting speed and cutting quality is useful, but the nozzle at low altitude may cause double arc phenomenon.
所以，选用尽量小的喷嘴高度对提高切割速度和切割质量都是有益的，但是，喷嘴高度过低时可能会引起双弧现象。
Four, arc voltage: generally believe that the power supply is normal output voltage for cutting voltage.
电弧电压：一般认为电源正常输出电压即为切割电压。
The arc cutting technique of air plasma water re-compressed won the second prize of National Scientific and Technological Progress Award.
科研项目空气等离子水再压缩弧切割技术获国家科技进步二等奖。
Five, the nozzle height: refers to the nozzle surface and cutting the distance from the end, it constitutes the part of the whole arc long.
喷嘴高度：指喷嘴端面与切割表面的距离，它构成了整个弧长的一部分。
Now the plasma arc cutting machine part on gas pressure to control the flow, because when gun aperture, the gas control certain pressure and you control the flow.
现在的等离子弧切割机大多靠气体压力来控制流量，因为当枪体孔径一定时，控制了气体压力也就控制了流量。
Because the hydrogen can significantly improve the arc voltage, make hydrogen plasma jet has high enthalpy, when mixed with argon plasma jet, the use of cutting ability is greatly increased.
由于氢气能显著提高电弧电压，使氢等离子射流有很高的焓值，当与氩气混合使用时，其等离子射流的切割能力大大提高。
To reduce the kerf width and to improve the kerf quality, the experiments of ceramic cutting with water constricted plasma arc are carried out.
为减小切口宽度，提高切口质量，进行了水再压缩等离子弧切割陶瓷实验研究。
In the finality of this article an experiment study about plasma arc cutting variable-thickness plate is introduced.
本文的最后部分对等离子体弧切割变厚度板材进行实验研究。
Electric arc welding or cutting is performed.
电焊或电切割时。
This paper introduces the experiment condition and process to carry out hot cutting on silicon nitride ceramics materials with new self-made water-plasma arc equipment.
主要阐述了采用自制新型水介质等离子弧设备对氮化硅陶瓷材料进行加热辅助切削的试验条件及过程。
And has a CNC vertical lathe, boring machine large landing, automatic gap submerged arc welding, electro-optical tracking cutting machine and a variety of measurement test equipment.
且拥有数控立式车床、大型落地镗床、自动间隙埋弧焊、光电跟踪切割机以及各类计量检测设备。
This paper analyzes the basic structure, work principle, usages and notice items of PC-60 air plasma arc cutting machine, and lists the common trouble phenomena, causes and solutions.
分析了PC - 60型空气等离子弧切割机的基本结构、工作原因、使用方法和注意事项；例举了其常见故障现象、产生原因和排除方法。
For duplex stainless steel thermal cutting shall be limited to the plasma arc method.
对双相不锈钢进行热切割应该仅限于等离子弧切割方法。
Steady arc and fast cutting, even cuts, little deformation and slag, material-saving.
切割电弧稳定，切割速度快，切口平滑，变形小，挂渣少，节省材料。
Plasma arc cutting is a physical process which utilize high temperature to heat materials and high speed flow to blow melted metal, cutting quality is directly influenced by arc power and arc force.
等离子体弧切割是通过高温等离子体弧将工件弧柱部分的材料熔化并利用高速离子流将切渣吹除的物理过程，弧柱的功率和作用力将直接影响到切口质量。
The whole procedure includes preparing steel strip and butt welding, forming and fixed position welding, pipe output and cutting, and final submerged arc welding.
其整个工艺包括带钢准备和对接、成型及定位焊、管子输出和切割和埋弧终焊。
The air plasma arc cutting technology is worthy to popularize a new thermal cutting technology.
空气等离子弧切割工艺是值得推广的热切割新技术。
The effects of cutting area, contact arc length, the geometry of cutting face, back dip angle of PDC cutter and rock performance on force of PDC cutter breaking rock were simulated experimentally.
试验模拟了切削面积、接触弧长、切削面形状、切削齿后倾角和岩石性能对PDC切削齿破岩受力的影响。
Companies with welding, carbon dioxide gas shielded arc welding, argon, carbon arc gouging, oxygen cutting and other special operations personnel.
公司具备电焊、二氧化碳气体保护焊、氩弧焊、碳弧气刨、氧气切割等特种作业人员。
According to the change pattern of some parameters in metal cutting processes, this paper proposes for the first time a new time series analysis model-Autoregressive Constant model ARC (2).
本文根据切削过程中一些参数的变化规律，从理论上首次提出了一种新的时间序列分析模型，即常系数固定价ARC(2)模型。
精细等离子弧切割。
This paper analyses the usage of LGK series of air plasma arc cutting machine, and enumerates the causes and solutions of striking arc, main circuit, gas path and cutting torch breakdown.
分析了LGK系列空气等离子弧切割机的使用方法，例举了其引弧故障、主电路故障、气路故障、割枪故障产生的原因和解决方法。
The basic principle, test device, and the regularity of cutting parameters affecting to the arc characteristics, kerf width, kerf Angle, and dross free cutting speeds are dealt with.
内容涉及基本原理、实验装置及加工参数对弧柱特性、切口宽度、切口角、无渣切速的影响规律。
The basic principle, test device, and the regularity of cutting parameters affecting to the arc characteristics, kerf width, kerf Angle, and dross free cutting speeds are dealt with.
内容涉及基本原理、实验装置及加工参数对弧柱特性、切口宽度、切口角、无渣切速的影响规律。
应用推荐