• The influence of the leading Angle (lagging Angle) of the current reference signal the parameters and drive mode of the system to the dynamic characteristics are analyzed.

    着重分析了电流参考信号超前角(滞后角)、系统参数和驱动方式对无刷直流电动机系统动态性能的影响。

    youdao

  • By comparing the heating effect of an unknown AC signal to that from a known DC reference, metrologists can determine the RMS AC quantity (voltage or current) in terms of the DC quantity.

    为了对比一个已知直流参考的未知交流信号热效应,计量人员可以确定在一段时间内直流的交流有效值(电压或电流)。

    youdao

  • The reference signal in this control approach is obtained by detecting both source current and load voltage.

    该控制方式的指令信号通过同时检测电源电流和负载电压得到。

    youdao

  • A prediction error signal and a motion vector for a current block are transmitted, describing the location of the predictor block in the reference picture.

    传输当前块的预测误差信号和运动向量,这描述了参考画面中预测器块位置。

    youdao

  • MSP430F449 has abundant internal resource, but itself 12 b A/DC negative pole reference voltage can′t be lower than 0V. It has brought the difficulty in measuring alternating current signal.

    MSP430F449单片机内部资源丰富,但是他本身自带的12位A/DC参考电压中的负极最低不能小于0V电压,对于交流信号的测量带来了困难。

    youdao

  • Each module is controlled by voltage current two closed loops. The common voltage loop controls system output voltage & frequency, and generates a common reference current signal.

    三台航空静止变流器模块均为电压、电流双环控制,通过公用电压调节器稳定并联系统的输出电压及频率,同时产生统一的模块电流给定信号。

    youdao

  • Receiving the third signal and based on a reference voltage, the switching circuit controls the pulse wave width of the switching signal so as to adjust output current of the power converter.

    切换电路接收第三讯号并依据一参考电压,以控制切换讯号的脉波宽度,所以可调整功率转换器的输出电流。

    youdao

  • Each module is controlled by voltage-current two closed-loops. The common voltage loop controls system output voltage & frequency, and generates a common reference current signal.

    每台航空静止变流器模块均为电压、电流双环控制,通过公用电压调节器稳定并联系统的输出电压及频率,同时产生统一的模块电流给定信号。

    youdao

  • The latter USES the last line height signal as the reference input of Z-control in the current line scan.

    后者利用前一行扫描高度数据作为当前行z向扫描器驱动的参考输入。

    youdao

  • The latter USES the last line height signal as the reference input of Z-control in the current line scan.

    后者利用前一行扫描高度数据作为当前行z向扫描器驱动的参考输入。

    youdao

$firstVoiceSent
- 来自原声例句
小调查
请问您想要如何调整此模块?

感谢您的反馈,我们会尽快进行适当修改!
进来说说原因吧 确定
小调查
请问您想要如何调整此模块?

感谢您的反馈,我们会尽快进行适当修改!
进来说说原因吧 确定