Therefore, you should improve on UV curing speed or select efficient UV curing light source.
因此，应提高UV上光油的固化速度或选择高效的紫外固化光源。
The factors which influenced adhesive strength, curing speed of reactive polyurethane hot melt adhesive were studied.
考察了各因素对反应型聚氨酯热熔胶粘接强度、固化速度等性能的影响。
This article has researched the effect of photoinitiator types and concentration on the curing speed and thickness of the vinyl resin.
研究了光引发剂种类、浓度对乙烯基树脂光固化速度、厚度的影响。
The introduction of polyurethane groups to the blend improved the adhesivity, hardness, curing speed and surface energy of alkyd resin.
由于在共混物中引入了芳香族氨酯键，增加了醇酸树脂漆膜的附着力、硬度、固化速度及表面能。
The results showed that when compared with SBR, the NBR filled with calmos CC had higher tensile strength and tear strength, but lower curing speed.
结果表明，随着白燕华CC用量的增大，胶料表现出比填充非极性SBR更高的拉伸强度和撕裂强度，而硫化速度却明显减慢。
Catalyst mixtures also have effects on the improvement of curing speed and reduction of surface-free time, with simultaneously the increase of viscosity.
研究还发现，采用混合催化剂也能够显著地提高密封胶的交联速率，缩短表干时间，且对其力学性能不会产生显著影响。
The resin produced by the flame-retardant products with high strength and mechanical properties, thermal deformation temperature, curing speed, and good soak.
该树脂所生产制品具有很高的阻燃性能和机械强度，热变形温度高，固化速度快，浸透性好。
This article has reviewed the influence of photoinitiators, monomers, prepolymers, and pigments on the curing speed of UV-curing coatings, and its development trend.
综述了光引发剂、单体、预聚物、颜料等因素对紫外光固化涂料固化速度的影响，及其研究方向。
Resin curing speed bears a relation with the temperature, the higher temperature, the quicker curing, and it spends about one hour for curing under normal temperature.
树脂固化速度与温度有关，温度越高固化就越快，在常温下约为一小时。
The experimental results show that the deeper layer's curing speed of the ink system mainly depend on the type and the amount of the sensitizer and the hydrogen donor.
研究了复合引发体系的组成、配制方法、油墨加工方法对固化速度，特别是深层固化速度的影响。
As for the performance of UVcured optical fiber buffer coating, the main concerns are the curing speed, strength, stripping force and additional loss of the buffer layer.
紫外固化光纤缓冲层涂料性能，主要考虑的是缓冲层涂料的光固化速度、缓冲层的强度、缓冲层的剥离力及缓冲层的附加损耗等性能。
As the increase of age, the use of mother tongue to deepen its curing process, therefore, to eliminate the interference of mother tongue will be more difficult, affected the speed of learning English.
随着年龄的增大，母语的使用加深了其固化的过程，因此，消除母语的干扰会更加困难，影响了英语学习的速度。
The major factors to affect curing degree of optical fiber coating at high drawing speed based on the existing drawing tower.
主要讲述了拉丝塔提高光纤拉丝速度过程中，影响光纤表面涂层固化度的几个因素。
The curing rate of both the free radical and cationic UV curable coatings are accelerated with the rise of temperature, and the former's cure speed is higher than the latter.
V自由基固化和阳离子固化的固化速度随温度的升高而加快，并且自由基的固化速度大于阳离子固化速度。
A new lag inflating curing agent could be developed by controlling the expanding speed properly.
通过对快速膨胀变形的适当控制，可开发出滞后膨胀式脱模养护剂。
The features of PC X43R300 type hydraulic curing press for high speed passenger car radial tire and the influence of curing process parameters on tire quality are described.
介绍了pcx43r300型液压硫化机在高速度级轿车子午线轮胎生产应用过程中的特点及硫化工艺参数的确定对轮胎质量的影响。
Room temperature curing, high speed, help increase production.
室温下固化，速度快，有利于提高产量。
Can be controlled by temperature and inorganic non-metallic high-temperature activator hydration activity of plugging the excitation and the thickening and hardening speed and strength after curing.
可以通过温度和活化剂控制无机非金属高温调堵材料水化活性的激发及稠化、硬化速度以及硬化后的强度。
Can be controlled by temperature and inorganic non-metallic high-temperature activator hydration activity of plugging the excitation and the thickening and hardening speed and strength after curing.
可以通过温度和活化剂控制无机非金属高温调堵材料水化活性的激发及稠化、硬化速度以及硬化后的强度。
应用推荐