The piercing principle of 2-roll cross-rolling piercer and its application range are discussed.
论述了二辊斜轧锥形辊穿孔机的穿孔原理及其应用范围。
Cold-cross-rolling is a new cold processing technique espevially applicable for technical improvement of middle-small size enterprises.
冷斜轧是一种适应中小型无缝钢管企业改进工艺的新型钢管冷加工工艺。
The conclusion provides some of theoretical basis for the further research of the three-cross-rolling technology and practical operation. It has some theoretical significance and practical value.
本课题的研究为进一步研究外螺纹三辊斜轧工艺和生产提供了部分理论依据，具有一定的理论价值和现实意义。
The energy consumption (EC) characteristics of asymmetric and cross rolling (AC) technology were analysed by rolling theory and translated principle of power.
采用纵轧理论和功率转换原则对异步交叉轧制的能耗特性进行了分析，并进行了实验验证。
In this stage semifinished products with smaller cross sections are produced, such as slab, bloom or billet, which are suitable for further rolling.
这个阶段的产品是横断面较小的半成品，如板坯、大钢坯、小方坯等。这些半成品适合于进一步轧制。
Two formulas for calculating any roll configurations of a rolling mill are derived by means of coordinate transformation and variable replacement from the cross rolling characteristics.
根据斜轧特点，利用坐标变换和变量代换方法，导出了两种计算任何斜轧辊形的公式。
I'll take her cross the rolling water.
我要和她一起渡过滔滔的流水。
This paper introduces characteristic of cross rolling technology and its application in forging products of left continuous motion stem on automobile.
介绍了楔横轧工艺特点及其在汽车左连动杆锻件制坯中的应用，说明了模具设计工艺参数的选取和现场调试方法。
Based on the modeling method, design feature and manufacture feature of cross wedge rolling tool are founded.
并且根据该建模方法，建立了楔横轧模具的设计特征和制造特征。
HanYingchun. Wang Xueming. Chen Yubao the new technology of the forward extrusion and cross rolling for the rear axle shaft sleeve of light truck.
韩英淳。王学明。陈义宝农用运输车正挤与横轧式后桥半轴套管。
The study provides effective numerical analysis method and theoretical basis for the design and optimization of automobile semi axle cross wedge rolling.
研究结果为优化和设计汽车半轴楔横轧设备提供了有效的数值分析方法和理论依据。
The equations of different helix in cross wedge rolling in different coordinates were studied in this paper.
本文详细研究了不同旋向楔横轧成形螺旋面在不同坐标下的方程。
The effect of speed ratio on the texture of non-oriented cold rolled low silicon steel sheet was investigated after cross shear rolling at different speed ratios.
选取低硅无取向硅钢常化态板材，分别在不同速比下进行异步轧制，考察了速比对低硅无取向硅钢冷轧织构的影响。
The results have important role on further theoretical research, and improving the technical process and spreading area of application for cross wedge rolling.
研究结果对深入进行楔横轧理论研究，提高其工艺水平，扩展其应用范围有重要作用。
Technological experimental research for cross wedge rolling technology of pin valve of oil pump has been introduced with problems and relevant solutions during the process.
介绍了油泵油嘴针阀体的楔横轧工艺试验，以及在试验中遇到的问题及解决方法。
Based on the analysis of the process of cross wedge rolling during wedge in, the geometry model of rolling area is established.
在对楔入轧制过程分析的基础上，建立了辊式楔横轧楔入轧制接触面的数学模型。
In the rolling procedure of cross wedge rolling, the technological parameters and instantaneous rotational speed ratio of workpiece and roller have intimate and complicated relationship.
轧件与轧辊的瞬时速比和楔横轧工艺参数之间存在着十分密切而复杂的联系。
Using numerical computation of fluid flow, the coefficients of vertical force, lateral force and rolling moment caused by cross-wind were calculated, which were related to train speed and wind speed.
采用流场数值模拟计算方法，计算了横风作用时的垂向气动升力系数、气动横向力系数和侧滚力矩系数，得出各系数与车辆速度和风速之间的变化关系。
The cross wedge rolling mill's hydraulic screwdown imitative experimental device is used for simulating practical system on parameters and control method determination.
楔横轧机液压压下模拟实验装置，可以模拟实际系统进行的参数选择，各种控制方法的实验。
I'll take her 'cross the rolling water.
我要和她一起渡过滔滔的流水。
In this paper, an idea of toward intelligent CAD system of cross wedge rolling dies is introduced.
本文提出了基于智能方法的楔横轧模具CAD的总体思想，旨在解决模具设计的自动化问题。
Based on the analysis of the process of plane type cross wedge rolling, the geometric model of workpiece forming has been established.
在对板式楔横轧轧制过程分析的基础上，建立了楔横轧楔入轧制和展宽轧制过程中轧件变形的数学模型。
The result provides theoretical base for numerical simulation of 6061 aluminium alloy in the process cross wedge rolling deformation of three dimensions.
这些分析结果对于深入认识6061铝合金变形行为提供了理论上的支持，并为数值模拟6061铝合金的楔横轧三维变形提供理论基础。
The criterion that should be obeyed as designing the die transition of cross wedge rolling was expounded in theory.
从理论上阐明了设计楔横轧模具过渡段应遵循的准则。
The type, application, technological parameters and die structure of the cross-wedge-rolling technology were introduced.
介绍了楔横轧工艺的类型、应用、工艺参数及模具结构。
The metal fluidity in deformed rigion was stutied by comparing commen rolling with cross rolling and experied with two high cold rolling mill.
对常规轧制和交叉轧制时变形区金属流动特性进行了理论分析 ，并在二辊冷轧机上进行了试验。
The article has introduced the cross wedge rolling preforming technology and its die design.
介绍了楔横轧制坯工艺及其模具设计。
The article has introduced the cross wedge rolling preforming technology and its die design.
介绍了楔横轧制坯工艺及其模具设计。
应用推荐