It is superior to natural rubber because of its high abrasion resistance, excellent heat resistance and low temperature properties and good resistance to light crazing.
它优于天然橡胶，因为它具有高抗磨性、优异的耐热性和低温性能，以及良好的抗光照开裂性。
It machines easily, but internal crazing often develops.
它易于加工，但是内部常常会出现裂纹。
The crazing phenomenon is unique to amorphous glassy polymers.
银纹化是玻璃态高聚物所特有的一种现象。
At present, the main destruction phenomenons that epoxy mortar used in a large scale include aging, crazing, disengaging etc.
目前环氧砂浆大面积应用出现的主要破坏现象为老化，开裂，脱空等。
The dissertation concluded the character of bearing, the case of stress distributing and anti-crazing capability via the research about the result of computing.
通过对计算结果的分析研究，总结了其受力特点、应力分布情况和抗裂性能。
This paper states the causes and prevention measure of longitudinal crazing of joints of pre - cast floor slab from the aspects of design, construction and material.
本文从设计、施工、材料等方面论述了预制楼板板缝纵向开裂产生原因及防治措施。
The surface of bitumen pavement is always affected by climate factor and some kinds of load that lead to some road diseases such as crazing, relaxing, distortion and so on.
沥青道路面层受到各种气候因素、荷载作用的影响，经常发生开裂、松散、变形等病害。
It could manufacture products with the effects of laser, crazing, placer gold, bright gold, grit finish, pearl light, crystal, hollow cutting, black nickel and invisibility.
可制作镭射、网纹、沙金、亮金、磨沙、珠光、水晶、镂空、黑镍、隐形等各种效果的产品。
Silica aerogel crazing was analyzed and some improvements were made using TMCS surface modification technique together with the drying media of normal-hexane to control the crazing.
在分析气凝胶干燥开裂的原因后，以三甲基氯硅烷（ TMCS）为表面修饰剂， 正己烷为干燥介质的表面改性工艺，一定程度控制了气凝胶的干燥收缩和开裂。
This article analysis the cause of crazing defects in big and irregular fine potteries from materials, forming, firing, and plaster moulding etc. Then some feasible ways are brought up.
针对精陶大型、异型产品的开裂缺陷，从泥料、成型、烧成、石膏等多方面加以分析，从而找出了导致产品开裂的主要因素，提出了切实可行的解决方法。
V-shaped notch blasting is that cutting slots with certain depth along axis -direction of the hole is determined according to the blast-crazing, and then load uncoupled charge and detonation.
形刻槽爆破是指在炮孔孔壁上按爆破开裂方向，切出一定深度的轴向对称V形槽，采用不耦合装药结构进行的一种断裂控制爆破。
Crazing is the invariable precursor of brittle fracture.
出现小裂纹必然是脆性断裂的前兆。
Crazing is a typical kind of nonlinear deformation in brittle polymers.
银纹化是脆性高聚物的一种典型的非线性变形方式。
Crazing is a typical kind of nonlinear deformation in brittle polymers.
银纹化是脆性高聚物的一种典型的非线性变形方式。
应用推荐