Similarly, in the crankshaft journal and crankshaft bearing clearance measurements, they can draw on such skills.
同样,在进行曲轴轴颈和曲轴轴承配合间隙的测量时,也可以借鉴这种操作技巧。
The reasons include inappropriate maintenance, component failures, filter blockage, bad crankshaft bearing shells, inappropriate fit clearances, abnormal diesel engine vibration and etc.
烧损原因包括保养不当、部件故障、滤清器堵塞、轴瓦质量不高、配合间隙不合适以及柴油机异常振动等。
The second photo shows the crankshaft center bearing holder installed in the block.
第二图为曲轴中心轴承持有人安装在该区块。
The crankshaft has three main bearing journals.
曲轴有三个主要轴承期刊。
The key position bolt of the engine include connecting rod, crankshaft, main bearing, cylinder head, flywheel and shock absorber bolt, all of which belong to bolt fastening.
发动机关键工位螺栓包括连杆螺栓、曲轴螺栓、主轴承盖螺栓、气缸盖螺栓、飞轮螺栓和减振器螺栓等均属螺纹联接。
Applying the slender crankshaft, the level rolling bearing technology, and lower viscosity refrigeration oil, increased the mechanical efficiency.
采用细曲轴及平面滚动轴承技术及较低粘度的冷冻油以提高机械效率。
Pilot bearing in crankshaft. The pilot bearing in the crankshaft is usually either a Bushing or a Ball bearing.
曲轴上的导向轴承:曲轴上的导向轴承一般或者是轴瓦,或者是球轴承。
The idea of using split hydrostatic bearing as the support bearing of crankshaft in oxygen compressor to replace the split sliding bearing was proposed.
提出用剖分结构的静压轴承作为氧气压缩机曲轴支承轴承,取代轴瓦剖分形式的滑动轴承。
The counterweight is installed on the crankshaft for reducing the bending moment on it, but it will influence the magnitude and distribution of the main bearing load.
曲轴上平衡重的安装减小了曲轴所受的弯矩,但也影响了主轴承载荷的大小和分布。
Then, the coupling of tribology, stiffness and strength of crankshaft-bearing system for internal combustion engine is studied.
在此基础上,进行了内燃机曲轴—轴承系统摩擦学、刚度和强度的耦合研究。
The reasonable disposition of the crankshaft counterweight can minimize the maximum load on the main bearing, it is another problem of the design of the counterweight.
合理地布置平衡重的位置以使主轴承载荷的最大值达到最小,这是平衡重设计的又一问题。
By analyzing reasons for break of engine crankshaft journal and bearing, this paper describes mainly some countermeasures they are break in use and maintenance.
通过对发动机曲轴轴颈与轴承损坏原因的分析,重点阐述了发动机在使用与维修中预防损坏的措施和方法。
A new structure for fixing the bearing bush of the connecting lever in a crankshaft press is introduced.
针对曲轴压力机连杆上轴瓦的固定问题,介绍了一种新的固定结构。
The bearing loads and crankshaft fatigue strength are calculated according to the principle of a simple beam.
轴承负荷及曲轴疲劳强度的计算均按简支梁进行。
The crankshaft passes through the lateral plate, the separator plate and the two compression cylinders, and is supported by a bearing between the two lateral plates.
曲轴穿过侧板、隔板及两个压缩缸,并由两个侧板内的轴承支撑。
Crankshaft: Alloy steel with whole bearing supporting and bearing and round corner harden.
曲轴:合金钢,全支承、轴颈和圆角淬火。
Crankshaft: Alloy steel with whole bearing supporting and bearing and round corner harden.
曲轴:合金钢,全支承、轴颈和圆角淬火。
应用推荐