Under certain pre - tension from flange joint bolt, leakage of flange sealing had an obvious decrease, thus resolving sealing failure in cover flange of heat exchange.
在一定法兰连接螺栓预紧力作用下，法兰密封泄漏明显减少，从而解决了热交换器封头法兰密封失效的问题。
Reattach the relief valve hose to the elbow in the bottom flange cover.
重新将安全阀软管接到底部法兰盖内的弯头上。
When cleaning, unscrew the head bottom plug, drain fluid, remove the flange cover, remove the filter basket, cleaning and re load can, therefore, maintenance is extremely easy to use.
当需要清洗时，旋开主管底部螺塞，排净流体，拆卸法兰盖，取出滤篮，清洗后重新装入即可，因此，使用维护极为方便。
This paper is based on the sealing reliability of flange for the DSHE and submits a predicting calculation' s method of the bolt for seating gasket used in circular-shaped cover of the DSHE.
本文以确保螺旋体法兰密封面的密封性能为前提，讨论了一种用以确定可拆螺旋板式换热器大平盖螺栓预紧力的估算方法。
Turn the hollow bolt so that it is fixed on the bake cover or the flange plate.
安装后必须旋出空心螺栓锁紧在电机后端盖或法兰盘上。
The installation 1, Qudiao flange end of the Flange-connection fixed ball valve protective cover on both sides, in the valve fully open state to wash clean.
安装1、取掉法兰端两边的保护盖，在阀完全打开的状态下进行冲洗清洁。
The finite element mould is set up to stimulate the contact condition between the flange of shell and the cover of dryer which proved to be correct by the result of stress measurement of1500dryer.
建立模拟烘缸缸体与缸盖法兰间相互接触状况的有限元计算模型，并用1500烘缸的应力实测结果验证计算模型的正确性。
Apply to reciprocating motion of hydraulic cylinder piston rod sealed device can also be used to cover the static flange seal.
适用于液压缸活塞杆往复运动用密封装置，也可用于法兰端盖的静密封装置。
Remove the bottom flange cover.
拆卸底部法兰盖。
Rugged die cast aluminum flange and cover.
坚固耐用的压铸铝法兰和覆盖。
Remove cover and clean flange and reseal.
拆卸车轴护罩，清洁凸缘并重新密封。
The new scheme is put forward to design magnetic pulley with large torsional moment by means of planar contact between end-cover and added flange fixed axially by stud bolt.
提出了用圆筒两端加制法兰与端盖平面接触轴向螺栓连接的方法设计大扭矩磁滑轮的方案。
The swing motor comprises a swing motor shaft core, a left end cover, a stator, a rotor, a vane, a right end cover, an output flange, a sensor and a conical roller bearing;
它包括摆动马达轴芯、左端盖、定子、转子、叶片、右端盖、输出法兰、传感器和圆锥滚子轴承；
The manufacturability of a fixing cover with flange seal was analyzed. The general structural design and layout scheme of a progressive die for the cover were presented in detail.
分析了带凸缘密封固定盖的工艺性，介绍了级进模总体设计结构和排样设计。
If meet the water pipe exports, ceramic tile to small incision, convenient and appropriate for the flange cover on water cover incision, makes appearance perfect.
如果遇到水管出口，瓷砖的小切口、方便和适合当前法兰盖上盖，使水切口外形完美。
For the cover of rolled stainless steel plate welded shape, cover and vacuum sealing flange at the end of the trough of large vertical lathe machining fine car molding.
内罩为不锈钢板卷制密焊成型，罩底法兰和真空密封槽由大型立车精车加工成型。
The sealing cover (5) is sealed on a flange section (6) of the packaging shell (3) and can be detached from the packaging shell in order to open the packaging chamber (4) along the sealed connection.
密封盖(5)密封到包装壳体(3)的凸缘区(6)上，并且为了打开包装腔室(4)，密封盖(5)可沿着密封连接与包装壳体(3)分开。
The sealing cover (5) is sealed on a flange section (6) of the packaging shell (3) and can be detached from the packaging shell in order to open the packaging chamber (4) along the sealed connection.
密封盖(5)密封到包装壳体(3)的凸缘区(6)上，并且为了打开包装腔室(4)，密封盖(5)可沿着密封连接与包装壳体(3)分开。
应用推荐