The results show that self-shielded flux-cored welding wires have better mechanical properties and wider applied scope than submerged arc welding wires in repairing the continue cast rollers.
结果表明，修复连铸辊，自保护焊丝比埋弧焊丝具有更好的力学性能及更宽的应用范围。
This paper has explained the manufacture principle of Al-flux-cored welding wire, and studied the technical characteristics of Aluminium alloy welding with straight polarity direct current TIG method.
阐述了药芯铝焊丝的制造原理，研究了TIG直流正接焊接铝合金的工艺特点。
Compared with cored wire, the solid wires have not so good welding usability showing oxidized and crinkled weld appearance as the welding parameters are greater.
而对于实心焊丝，在较大焊接工艺规范下，很容易出现焊缝表面的氧化起皱，焊缝成型不良。
However, in most cases, only the use of welding method, cored wire solder in the pin-hole-shaped tail.
但多数情况下，只能采用焊接的方法，将芯线焊在孔形插针的尾部。
At the special request of the flux-cored wire welding underwater, the welding arc control system is developed.
根据药芯焊丝水下焊接的要求，研制了一套水下焊接电弧控制系统。
With austenitic welding material, solid wire, flux-cored wire and electrode, welded joint mechanical property of TCS ferritic stainless steel all can meet usability.
T CS铁素体不锈钢采用奥氏体型焊材，实芯焊丝、药芯焊丝和电焊条方法，焊接接头力学性能可以满足使用要求。
The welding experiment and procedure qualification for manual TIG welding of stainless steel tubes with flux cored electrode is presented in this paper.
介绍采用药芯焊丝手工钨极氩弧焊焊接奥氏体不锈钢管道所进行的焊接试验及工艺评定。
The hardfacing alloy was deposited onto a low carbon steel substrate by self-shielded arc welding using nitrogen alloying self-shielded hardfacing flux-cored wire.
硬面合金是利用研制的氮合金自保护硬面药芯焊丝在低碳钢板上堆焊得到。
The percentages of the flux composition in YJ657 basic flux cored wire which affected the welding technology of basic flux cored wires had been studied.
研究了YJ657碱性药芯焊丝药芯粉的成分配比对焊接工艺性能的影响。
Flux-cored wire is applied to the austenitic stainless steel pipe by back weld, MAG for the filling and cosmetic weld, at horizontal fixed round welding vertically up.
采用药芯焊丝对奥氏体不锈钢管道进行打底焊接，MAG焊填充及盖面焊，立向上的水平固定全位置焊接。
In view of the special circumstances of the flux-cored underwater welding, a rule self-tuning fuzzy controller with modification function is designed here.
根据水下焊接的特殊情况，设计了一种带修正函数的规则自调整模糊控制器。
Technological process of CO2 gas shielded metal arc welding with stainless flux cored wire used for stainless steel tank construction is presented in this paper.
介绍了采用不锈钢药芯焊丝CO2气体保护焊焊接不锈钢储罐的工艺过程。
WC-cored electrode is a repair welding electrode with high hardness and high wear resistance, which has been widely used in circumstance with violent wear.
WC型管状焊条是一种高硬度、高耐磨性的堆焊焊条，广泛用于强烈磨损的零件上。
The wear resistance of surfacing layer was investigated by the design of flux-cored wires and tig welding method.
通过药芯焊丝配方的设计，结合TIG焊接方法，对堆焊层的耐磨性进行了研究。
English Name:Welding consumables - Tubular cored electrodes for metal arc welding with and without a gas shield of non alloy and fine grain steels - Classification;
简体中文标题：焊接材料。带和不带气体保护的合金钢以及细晶粒钢电弧焊用管状焊条。分类。
English Name:Welding consumables - Tubular cored electrodes for metal arc welding with and without a gas shield of non alloy and fine grain steels - Classification;
简体中文标题：焊接材料。带和不带气体保护的合金钢以及细晶粒钢电弧焊用管状焊条。分类。
应用推荐