Then the shape parameter can adjust the curves 'shape with the same control polygon.
形状参数可以在同一个控制多边形内调整曲线的形状。
With increasing of the shape parameters the curve can well approximate the control polygon.
当形状参数增大时，曲线能连续逼近控制多边形。
Moreover the shape of the quasi Bézier curves with the same control polygon can be adjusted by changing the shape parameter value.
对给定的控制多边形，可以通过改变形状参数的值来调整曲线的形状。
As the increase o the value of a shape parameter, the curves approach locally the control polygon constructed by the interpolation points.
曲线表示式中带有一个局部形状参数，随着一个局部形状参数值的增大，所给曲线将局部地接近插值点构成的控制多边形。
This paper present a sufficient and necessary condition of constructing quintic PH curves and analyze the geometric meaning of the control polygon.
本文给出了构成五次PH曲线的充要条件，分析了其控制多边形的几何意义。
When fitting each contour line, the points measured by non - contact measuring system are as the top points about control polygon for forming EE spline curve.
在拟合每个轮廓线时，先用非接触测量系统测出的数据反算出ee样条曲线控制多边形的顶点。
The algorithm automatically identifies the point at which the NURBS curve has to be faired. Modifying locally the control polygon, the algorithm yields a NURBS curve with improved fairness.
此算法自动找出NURBS曲线需要修改的那一点，局部修改控制多边形，使生成的新曲线更加光顺。
You can see that each ring in the multi-polygon is transformed to a single sub-path in SVG, started with the m control character and terminated with Z to close the ring.
可以看到，多多边形中的每个环都被转换成sVG中的一个子路径，每个环以控制字符m开始，以Z结束。
If one-click topology isn't the right answer for every situation, you can intuitively take control of the re-topology process with curves to assist in determining polygon flow.
如果一个点击拓扑不是任何情况下的正确答案，你可以直观的曲线重新拓扑的过程控制，协助确定多边形流。
The control points of the B3-spline to be constructed are computed simply by the vertices of the given polygon.
在算法中，所有的B3样条曲线的控制点可以通过对多边形的顶点简单计算产生。
Editing in 3d environment by a digital control plane, the method can deal with some geometry efficiently, such as point, line, and polygon, etc.
由数字控制平面的3d环境中的编辑，该方法可以处理一些几何效率，如点，线，多边形等。
A lot of experiments for open loop control and closed loop control have been made according to the polygon voltage vector control. The experiment result shows that the new scheme is feasible.
对于采用多边形电压矢量新方案，我们分别进行了大量的开环及速度闭环实验，实验结果表明本控制方案是可行的。
The control points of the rational spline to be constructed were computed simply by the vertices of the given polygon.
第二个算法不断删去多边形的凹点及新产生的凹点，最后得到凸壳顶点序列。
Classical direct torque control method adopts the technique of 6 polygon flux linkage voltage modulation. It will generate torque pulsation and harmonic interference.
传统直接转矩控制技术采用的六边形磁链电压矢量调制方法，这会引起较大的转矩脉动和谐波干扰。
Classical direct torque control method adopts the technique of 6 polygon flux linkage voltage modulation. It will generate torque pulsation and harmonic interference.
传统直接转矩控制技术采用的六边形磁链电压矢量调制方法，这会引起较大的转矩脉动和谐波干扰。
应用推荐