The goal was to create an enlarged contact sheet, or the entire 36 images on the roll to display in our home.
这个计划的目标是创造一个大相版，将这个胶卷上的36张照片挂在我们的家里面。
Notice how they make contact with the ground as they roll from heel to toe and then travel through the air to stride forward.
留意它们是如何从脚跟到脚趾接触地面，然后离开地面向前迈进。
Pronation is the gentle roll of a foot inward after making contact and it is normal and necessary for a foot to evenly absorb the impact of striking the ground.
脚内翻是脚触地后的稍微内翻，以均匀吸收触地后的冲力，这是一个正常而必要的的动作。
The roll separating force, rolling torque and contact pressure along the surface of the rolls are also evaluated by means of the finite element method.
轧制分离力、轧制力矩以及沿轧辊表面的接触压力也通过有限元法进行评估。
The paper discusses the necessity of applying double stepped backup rolls, and describes the methods for calculating the contact length and stepped depth and work roll crown.
论述了采用双阶梯支承辊的必要性。提出了接触长度、阶梯深度及工作辊凸度的计算方法。
Comprehensive function of varying contact length backup roll (VCR) is analyzed by using the finite element model for elastic deformation of rolls.
利用建立的有限元辊系弹性变形模型，分析了变接触支持辊(VCR)的综合性能。
Four-point contact ball earings used for rolling mill roll the oil tank to withstand the axial load.
四点接触球轴承多用于轧钢机的油辊箱以承受轴向负荷。
In the mean time, the vertical and roll motions of the pantograph fame should be as small as possible, so that to make the contact force as normal as the conventional train.
并且使受电弓框架垂向位移和侧滚角度足够小，弓网接触压力达到车辆正常曲线通过时的水平。
The article bases on the result of elastic-optic experiment and uses the energy method, roll theory and thick tube theory to calculate the contact pressure in ringent and close section.
根据全息光弹实验结果得出的轧辊接触压力的分布规律，进而利用能量方法、轧压理论及厚壁筒理论对开口孔型、闭口孔型的轧辊接触压力进行计算。
FE method in RSD: observations FE methods are capable of predicting quite accurate deformation behaviour such as roll contact stresses, rolling load, and rolling torque required for RSD.
有限元方法rsd为：观测有限元方法是相当准确的预测能力变形行为，如辊接触应力，轧制负载和轧制力矩为区署要求。
The plane stress theory is applied to analyze the contact stress between cast track and roll wheel.
采用平面应力理论来分析滚轮与轨道的接触应力问题。
Based on production conditions and data, this article discusses the varying contact length back-up roll deformation under the condition of equal contact pressure between rolls.
以某中板厂生产条件和数据为基础，讨论了变接触长度支承辊辊间接触压力相等时的轧辊变形情况。
This article presents an analysis of the contact stress of rolls in two-cross-roll straightener and gives a method for the calculation.
在实践的基础上对二辊矫直机辊面接触应力的计算进行了理论分析，给出了辊面接触应力的计算方法。
The failure forms of cold work roll including contact fatigue crack, spalling, inclusion crack and wear are discussed.
讨论了冷轧工作辊接触疲劳裂纹、剥落、夹杂物裂纹和磨损等失效形式。
Using a developed modified influence function method, the cold rolling of thin strip in both symmetric and asymmetric cases were analysed with considering work roll edge contact.
在考虑工作辊边部接触的前提下，采用自行开发的改良影响函数法对薄带的对称和非对称冷轧过程进行了分析。
But the peak of contact pressure between rolls forms when the intermediate roll shifts, which leads local wear of rolls and quality defects of strip.
但由于中间辊轴向窜动后，在工作辊与中间辊、中间辊与支撑辊间形成接触压力峰值，导致轧辊局部磨损及带材表面质量问题。
Then carry on the contact analysis to roll pair, study the stress distribution situation between the roll pair.
然后再对轧辊副进行接触分析，研究轧辊副的接触应力分布情况。
In accordance with the theory of contact mechanics an analysis is made upon rolling bearings by means of finite element method and a new method of unsymmetric shape modification for roll...
根据接触力学理论，通过有限元方法对滚动轴承的分析，提出了滚子非对称修形新方法。
So I would roll, I'd make no eye contact — just kinda frown, right?
我滚动着，躲开视线的接触——就像一种皱眉，对么？
The surface of supporting roll and guiding roller, which contact with coiled metal, are covered with PU.
与钢带表面接触的托辊，护辊均采用聚氨脂包胶处理。
Plate projection system: a plat exposure system which works by projecting the image from microfilm or compact roll film rather than by the same-size one-to-one contact printing of films.
投影制版系统：用微摄菲林或小型卷筒菲林内的影像投射于印版上的晒版系统，有别于用原大菲林和接触晒印的方法。
Theelastic contact deformation between work roll and work-piece, work-piece deformation near the edge of plate and elastic recovery are discussed.
对板带轧制过程中轧辊与轧件的接触变形进行了分析，得到了轧辊弹性压扁、轧件边部减薄以及轧件弹复的分布规律。
The contact angles decrease, the roll angles increase, the antifouling performance gets small and the adhesion strength increase with the increment of space of the microstructure.
随着微结构间距的增大，接触角减小，滚动角增大，抗附着性能降低，附着强度增大。
Due to the expansive computational costs, the contact and deformation analysis of roll system are very difficult via using the conventional numerical methods, such as FEM or BEM etc.
但由于计算量很大，使用传统数值方法(有限元法或边界元法)分析辊间接触和辊系变形是非常困难的。
The paper mainly introduces a kind of parking roll management system based on contact - less IC card. The design idea, system composing and the main performance of the system are described.
本文介绍了一种基于非接触式IC卡的停车场收费管理系统的设计思路、系统组成及该系统的主要特点。
The effects of rolling parameters such as plate width, roll contours, chamfer and straight chamfer parameters on the contact pressure distribution were studied.
研究结果表明，在轧制能力范围内，轧件越宽，轧辊采用凹辊型可以使辊身部的辊间压力分布更为均匀；
The effects of rolling parameters such as plate width, roll contours, chamfer and straight chamfer parameters on the contact pressure distribution were studied.
研究结果表明，在轧制能力范围内，轧件越宽，轧辊采用凹辊型可以使辊身部的辊间压力分布更为均匀；
应用推荐