• The contact hole (19) has an elliptical planar shape.

    接触19) 的平面形状椭圆形

    youdao

  • Electrode contact hole USES heavily doped for reducing contact conduction loss.

    电极接触孔处采用掺杂减小接触电导损失

    youdao

  • Furthermore, the contact finite element was adopted to gain the accurate distribution of strength in the subassembly with the interference between the axle hole and the shaft.

    另外采用接触单元对孔轴过配合联接组件进行了有限元分析,得到更为精确强度分布

    youdao

  • The force and deformation of bottom hole assembly (BHA)are calculated by the gap-element method, in consideration for the bending effect and contact state of BHA.

    考虑下部钻具组合弯曲效应接触状态,运用间隙无法对下部钻具组合进行受力变形计算

    youdao

  • This is their second effort to make contact with the men. Yesterday a microphone was lowered down to a separate hole, but that also turned up nothing.

    他们第二次尝试矿工联系昨天迈克风放在一个洞里没有结果

    youdao

  • With the Kickstarter campaign completed, Grassell found a production facility through a contact in her hometown of Jackson Hole, Wyo.

    Kickstarter筹资项目完成后,格拉通过家乡怀俄明州杰克逊联系人找到了生产工厂

    youdao

  • The results of burned hole with optical fiber are better than those with surface contact.

    激光光纤后碎石表面接触碎石效果更好试验再现率81.8%。

    youdao

  • Furthermore, as for the fork blade roots, a simplified contact model is put forward and according to the calculation results, a more reasonable pin-hole load distribution model is given in this paper.

    另外叶根文中提出一种简化接触模型根据计算结果给出合理销钉载荷分布拟合公式。

    youdao

  • At the 4th floor, there is a functional combination: entertainment room, altar room, laundry room, a small garden and a roof with a hole to enable the direct contact with nature.

    第四功能性组合空间:娱乐室、祭祀洗衣房小型花园保证自然直接接触屋顶

    youdao

  • Contact problems between concrete base surface and column base, bolt nut and neighborhood plate, bolt shank and bolt hole are simulated really.

    有限元分析中模拟底板基础之间垫片底板之间、以及锚栓与混凝土之间的接触作用

    youdao

  • The tangency point of Bottom Hole Assembly is located at where the drill string just touches the wall of the borehole, and the contact force is zero here.

    计算底部钻具组合受力变形时,以前一般都按弯矩零的条件来确定其上切点位置

    youdao

  • Microcomputer controlled electro-contact touch needle is used to find center of the hole in X orientation and measure diameter in Y orientation.

    接触探针微机控制下,X方向中心,在Y方向进行孔径测量

    youdao

  • To measure the hole diameter, width and height of key by vernier caliper, if there is any discrepancy, PLS do not hesitate to contact us.

    游标卡尺,分别测量电机的轴径起动器孔径、、键高等尺寸是否相同,如差异,应及时本公司联系,以求解决。

    youdao

  • It is emphasized to the moving and rolling contact of 2d elastic bodies with hole-type defect or crack in the vicinity of contact region.

    这些算例着重接触区附近孔洞缺陷裂纹弹性体移动滚动接触。

    youdao

  • It is emphasized to the moving and rolling contact of 3d elastic bodies with hole-type defect in the vicinity of contact region.

    这些算例着重接触附近孔洞缺陷弹性体移动接触。

    youdao

  • The reservoir pellets take line, spot - line contact primarily, The cemented type is mainly hole, hole - contact cemented, The agglutinations are mainly clay minerals;

    颗粒线-线接触为主胶结类型主要为孔隙、孔隙-接触胶结,胶结物主要为粘土矿物;

    youdao

  • An extension line with a certain distance to the steel bar discharge hole is provided with a contact travel switch. A wire is connected between the travel switch and a clutch electromagnet.

    距离钢筋出料口一定距离的延长线设有一个接触式行程开关,行程开关离合器电磁铁之间连接有导线

    youdao

  • The results show that the position of the exhausting gas hole and the arc heat effects on the gas inside the hollow moving contact have obviously raised the pressure rising speed.

    利用它对国产OFPI—220型SF_6断路器进行的计算结果表明改变动头排气孔位置电弧动触头腔中气体热效应可明显提高开断电流时灭弧室压力上升速度。

    youdao

  • The equation of the edge curve of the slotting tool for machining the hole of the isometric profile cylinder (IPC) is developed by the principle of contact of the gears.

    等距型面孔插刀进行设计,对其平均半径、前角、后角、刀刃的空间曲线作了分析和研究。

    youdao

  • The equation of the edge curve of the slotting tool for machining the hole of the isometric profile cylinder (IPC) is developed by the principle of contact of the gears.

    等距型面孔插刀进行设计,对其平均半径、前角、后角、刀刃的空间曲线作了分析和研究。

    youdao

$firstVoiceSent
- 来自原声例句
小调查
请问您想要如何调整此模块?

感谢您的反馈,我们会尽快进行适当修改!
进来说说原因吧 确定
小调查
请问您想要如何调整此模块?

感谢您的反馈,我们会尽快进行适当修改!
进来说说原因吧 确定