• Adjust the steering wheel each contact gap.

    调节方向盘各个触点间隙

    youdao

  • Small contact gap, snap action, high sensitivity and small operating travel.

    具有微小触点间隙动作快速灵敏微小行程

    youdao

  • Stack contact area should be formed, when the contact gap, should be required to handle, as shown in table 5-3.

    接触面平整,接触间隙时,应按规定处理5 - 3。

    youdao

  • Press the horn switch, if the speaker sometimes ring, sometimes not ring, more than the inner contact of the switch is not good, the use of too long, the contact gap increases.

    喇叭开关如果喇叭有时,有时响,喇叭开关内部点接触不好使用时间过长,触点间隙增大。

    youdao

  • Filler must be well filled in order to minimize the gap, good contact between a single block of stone, as much as possible to fill in tight, stone cage to reduce the possibility of moving the stone.

    填料必须填写减少差距石头之间良好接触尽可能填写减少石头可能性

    youdao

  • End face with a gap, no boss butt is refers to the upper and lower casing left a certain gap between the upper and lower main chord rod end face at the same time contact.

    端面间隙台对接套管之间留有一定间隙,上、下端面同时接触对接。

    youdao

  • The contact point between the macrophage and lymphatic endothelium was deficient of junctions such as tight junction and gap junction.

    噬细胞淋巴管内皮细胞的彼此接触面缺乏紧密连接缝隙连接连接形式。

    youdao

  • In small tooth difference of inner meshed transmission, there were a few pairs of tooth faces which were apart from each other for a small gap beside the contact point generated by two meshed teeth.

    齿啮合传动中,存在接近啮合间隙齿理论啮合左右,轮齿受力产生的微小变形使得某些齿面相互接触进入啮合状态。

    youdao

  • The author used the contact theory to found the gap element, and used it to solve the contact force.

    利用现有的接触理论计算方法,在模型接触处构造间隙单元求解接触压力

    youdao

  • The gap element method is used to analyse two-dimensional elastoviscoplastic contact problem of circular tubes under explosive welding for the first time.

    首次采用间隙求解金属圆爆炸焊接时的二维粘塑性大变形接触问题管内包爆炸焊接的全过程作了详细分析

    youdao

  • The contact measurement is widely used to measure plate gap, but the method can't timely indicate the change of plate gap caused by plate wear.

    目前普遍采用接触式测量方法不能实时反映磨损后真实间隙

    youdao

  • The force and deformation of bottom hole assembly (BHA)are calculated by the gap-element method, in consideration for the bending effect and contact state of BHA.

    考虑下部钻具组合弯曲效应接触状态,运用间隙无法对下部钻具组合进行受力变形计算

    youdao

  • In the thesis, a non-contact measurement technology by combining an eddy current displacement sensor with a sonic thickness sensor was put forward to measure timely real plate gap of refiner.

    本文对采用涡流传感器超声波测厚组合实时接触测量磨盘真实间隙的设计方案进行了研究和探讨

    youdao

  • The numerical results indicate that the contact stress and strain, and the residual stress and strain increase as either of the switch gap, switch contact force, or electric current loads increase.

    分析结果显示,在本文分析之范围内,微继电器开关接触弯曲应力应变以及残留应力、应变均会随著开关间隙、接触以及电流负载之增加而增加。

    youdao

  • Unique nanotechnology, the Cramer diamond stone density without gap, bacteria have no place to hide, direct contact with food, non-toxic harmless.

    独有的纳米技术使得克拉美钻石英石致密细菌无处藏身,可食物直接接触无毒无害。

    youdao

  • In close contact with three smooth, is strictly prohibited in a gap between fold.

    三者依次平稳紧密接触,中间严禁间隙式褶皱

    youdao

  • End face with a gap, no boss butt is refers to the upper and lower casing left a certain gap between the upper and lower main chord rod end face at the same time contact.

    端面间隙、带台对接外形标准节上部杆上焊有定位凸台,定位凸台伸人另一标准节主弦杆内,上、套管之间留有一定间隙配合定位。

    youdao

  • The top end of the honeycomb tubular supporting component is fixed with the top plate by adhesive technology. The top plate does not make linear contact with the unfolded side, but leaves a gap.

    蜂窝管状支撑上方采用胶粘工艺固定顶层,顶层板底层板的曲折边形成线性接触,形成缝隙。

    youdao

  • Can you justify suppressing the mask under the air gap by making the "airgap" a contact resistance plate?

    不能合理地排除mask通过空气间隙做为接触热阻

    youdao

  • Can you justify suppressing the mask under the air gap by making the "airgap" a contact resistance plate?

    不能合理地排除mask通过空气间隙做为接触热阻

    youdao

$firstVoiceSent
- 来自原声例句
小调查
请问您想要如何调整此模块?

感谢您的反馈,我们会尽快进行适当修改!
进来说说原因吧 确定
小调查
请问您想要如何调整此模块?

感谢您的反馈,我们会尽快进行适当修改!
进来说说原因吧 确定