The console port does not support hardware flow control.
主控台埠不支援硬体流量控制。
This page will provide more information about the console port.
本页将提供更多关于主控台埠的资讯。
Connect to the switch using the serial console port with a straight serial cable (9600, 8-n-1, no flow control).
用串口直连电缆连接到交换机串行控制端口(9600、8 - N - 1、无流控制)。
Connect to the switch using the serial console port with a straight serial cable (9600, 8-n-1, no flow control) with default no user ID or password required.
用串口直连电缆连接到每台交换机的串行控制端口(9600、8 -N - 1、无流控制)，默认下不需要用户ID和密码。
First, connect to each switch using the serial console port with a straight serial cable (9600, 8-n-1, no flow control) with a default user ID admin and no password.
首先，用串口直连电缆连接到每台交换机的串行控制端口(9600、8 -n - 1、无流控制)，使用默认用户IDadmin，无密码。
Finally, make sure you set up the right console port in inittab; for the Soekris box, the default console speed is 19200kbps, rather than the 9600 Pebble Linux shipped with.
最后，请确保在inittab中设置了正确的控制台端口；对于Soekris机器，缺省的控制台速度是19200kbps而不是Pebble Linux所提供的9600。
Again, the administration console picks default names, which are a combination of the WSDL target namespace, the service name and the port name.
同样，管理控制台将选择缺省名称，它们是WSDL目标名称空间、服务名称和端口名称的组合。
The advanced options give you fine-grained control over Settings, such as port values, installation of the administrative console, and database configuration.
高级选项提供对各种设置细粒度的控制，如端口值、管理控制台的安装以及数据库配置。
Remember that if you are using that port number for the administrative console display, change the port number in your browser URL to redisplay the console.
记住，如果您在使用该端口号显示管理控制台，请更改浏览器URL 中的端口号以重新显示控制台。
What happens if you stop the listener port using the WebSphere Administrative Console?
如果使用WebSphere管理控制台停止侦听器端口，则会发生什么情况？
Next, configure WebSphere Application Server through the administrative console to listen for requests from Apache on port 443, then restart it.
下一步，配置WebSphereApplicationServer，通过管理控制台来监听来自Apache的443端口的请求，然后重新启动服务器。
When the message listener port is no longer referenced by any MDBs, it can safely be deleted, either via the administrative console or by wsadmin.
当任何MD B都不再引用消息侦听器端口时，可以通过管理控制台或wsadmin将其安全删除。
If this does not work, check the virtual host entries in the Application server admin console and ensure that a virtual host has been defined for the Web server's SSL port.
如果不能访问，检查ApplicationServer管理控制台中的虚拟主机条目，确保已经为Web服务器的SSL端口定义了虚拟主机。
If this does not work, check the virtual host entries in the Application server admin console and ensure that a virtual host has been defined for the Web server's HTTP port.
如果不能访问，检查ApplicationServer管理控制台中的虚拟主机条目，确保已经为Web服务器的http端口定义了虚拟主机。
You first need to determine the port on which the Rule Team Server console is running
首先，您需要确定RuleTeamServer控制台运行在哪个端口上
The default port will be configured in the WebSphere Administration console.
将在WebSphere管理控制台中配置缺省端口。
Finally, you can use the Registry and Repository console to check that the port contains the specified classification, as shown in Figure 11.
最后，可以使用Registry andRepository控制台检查端口是否包含指定分类，如图11中所示。
You first need to determine the port on which the Rule Execution Server console is running.
首先，您需要确定RuleExecutionServer控制台运行在哪个端口。
To get the port value, open the Application server administrative console and find the CEI server Application server bootstrap port address.
要获得端口值，请打开ApplicationServer管理控制台，并找到CEI服务器Application Server引导端口地址。
The BeagleBoard-xM provides a female DB9 port and requires a serial cable to connect the console to your host system.
BeagleBoard - xM提供一个DB 9凹口(female DB9 port)，需要一个串行电缆来将控制台连接到您的主机系统。
Note that if you do not specify a port name, a preferred port can be defined in the WebSphere Administration Console.
请注意，如果未指定端口名称，可以在WebSphere管理控制台定义首选端口。
Which resulting port is used for the Web service depends on the configuration of the preferred port in the WebSphere Administration Console.
将哪个端口用于Web服务取决于在WebSphere管理控制台中的首选端口配置。
The different port, which needs to match the "encrypted port" from the IManager console.
使用不同的端口，端口需要与iManager控制台中的“encryptedport”匹配。
You can fix any errors by bringing up an admin console manually. Search for the admin port in the server logs
您可以通过手动调出管理控制台来修复任何错误。
To ensure the desired port protocol is used, configure the preferred port in the Web services client binding configuration in the WebSphere Administration Console.
要确保使用所需的端口协议，请在WebSphere管理控制台的Webservicesclientbindingconfiguration中配置首选端口。
You will define the endpoint address for each port after deploying the service client application using the administrator console.
将在部署服务客户机应用程序后使用管理控制台为每个端口定义端点。
Depending on your configuration, you might need to adjust these port Numbers in the administrative console.
根据您的具体配置，您可能需要在管理控制台中调整这些端口号。
Set the port to the SOAP port number of the deployment manager (to find this, open the admin console, and look at System Administration => Deployment manager => Ports => SOAP_CONNECTOR_ADDRESS).
将端口 port设置为部署管理器的SOAP 端口号（为了找到这个，打开admin控制台，然后查看SystemAdministration =>Deploymentmanager =>Ports => SOAP_CONNECTOR_ADDRESS）。
Set the port to the SOAP port number of the deployment manager (to find this, open the admin console, and look at System Administration => Deployment manager => Ports => SOAP_CONNECTOR_ADDRESS).
将端口 port设置为部署管理器的SOAP 端口号（为了找到这个，打开admin控制台，然后查看SystemAdministration =>Deploymentmanager =>Ports => SOAP_CONNECTOR_ADDRESS）。
应用推荐