The host programs or loaders can then use this connection to transfer the bootloader onto the target, where it is written to flash.
然后，主机程序或装入程序可以使用这个连接将引导装载程序传送到目标上，并将它写入闪存。
This function also opens the connection to the host.
该函数还可以打开到主机的连接。
Specify your host connection information, including server name, network protocol, host name, service, and port.
指定您的主机连接信息，包括服务器名、网络协议、主机名、服务和端口。
If a host is listed in the file, SSH does not prompt the user for connection confirmation.
如果一个主机已经出现在这个文件中，那么SSH就不会提示用户确认连接。
This will trigger the scanned host to close the halfway-established connection again.
这将触发被扫描主机再次关闭已部分建立的连接。
With your collection of screen captures, you can work on the default rendering set offline until you are ready to test again with a live connection to the host.
利用您收集的屏幕截图，您可以脱机操作缺省呈现集，直到您准备再次通过与主机的连接进行测试为止。
A client initiates a connection to a host (and a specific port) by sending a syn synchronize packet.
客户机通过发送syn同步数据包发起到一个主机(和特定端口)的连接。
Each host USES a different connection to the controller to spread the load and maximize the throughput.
每个主机使用不同的连接连至控制器以分散负荷及最大化吞吐量。
If it isn't, there may be a problem with the physical connection from the network adapter on your host to the gateway (for example, a faulty switch port, cable, network card).
如果无法到达这个网关，那么从您主机上的网络适配器到网关的物理连接可能有问题（例如交换机端口、线路和网卡有故障）。
The simplest form of a TCP port scan is to open a connection to all ports on a host.
TCP端口扫描的最简单形式是打开一个到主机所有端口的连接。
This function attempts to make a database connection to the specified database located on a specified host with proper credentials.
这个函数尝试用正确的凭证连接位于指定主机上的指定数据库。
These connection properties include connection type, server host name, and the port that will be used to connect to the server.
这些连接属性包括用于连接服务器的连接类型、服务器主机名，和端口。
To accomplish this, the attacker sends a TCP packet with the SYN flag set to the target host, just like when opening a regular TCP connection.
要实现这一点，攻击者向目标主机发送设置了SYN标志的tcp包，就象打开常规tCP连接时一样。
A single SSH connection can host multiple channels concurrently, each transferring data in both directions.
单个ssh连接可以并行承载多个通道，每个都可双方向传输数据。
This should show that the connection has been established with the other host using UDP, shown in Listing 7.
这应该显示，已经使用UDP与其他主机建立连接，如清单7所示。
Before you log on, you should test your connection to the host.
在登陆之前，要测试与主机的连接。
In order to use the graphical installer of SUSE, there must be a direct network connection to the partition that will host the system.
为了使用SUSE的图形安装程序，必须要有一个到将要宿主系统的分区的直接网络连接。
As discussed above, when Host a wants to establish a TCP connection to destination Host d, it sends a TCP segment with the SYN flag set first.
如上所述，当主机A想建立到目的地主机d的TCP连接时，它首先发送设置了SYN标志的tcp段。
The connection is kept in a pending state while awaiting acknowledgment from the originator of the connection, Host a.
当等待连接的发起方(主机a)的确认时，连接保持挂起状态。
The client needs two pieces of information: the host name and the port number to which the connection will be established.
客户机需要两段信息：要连接的主机名和端口号。
The second line shows an ESTABLISHED connection, where 192.168.1.147 is connected to port 445 on the local host (192.168.1.143).
第二行显示ESTABLISHED连接，其中192.168.1.147连接到本地主机(192.168.1.143)上的端口445。
If this fails, it will then attempt to establish a connection with the standby SALES database located on host SVR2.
如果失败，它会尝试连接主机SVR2上的备用SALES数据库。
The URL Connection string does not support a designated host, and
URL连接字符串不支持指定的主机，而且
On theJVM Connection Details panel (Figure 9), specify the host name you wish to connect to and accept the default port number.
在JVM ConnectionDetails面板（见图9）上，指定要连接的主机名并接受默认端口号。
For example, if you open a Telnet connection to a particular host, the destination port will be set to 23.
例如，如果您打开到特定主机的Telnet连接，则目的地端口将被设置为23。
Steps 1-5 configure a connection to a demonstration host and create a LocalDemo Settings file that you can use for practice.
步骤1 - 5配置了到示范主机的连接并且创建了一个用于实行的LocalDemo设置文件。
Listing 5 shows part of the definition of the source named catalog - the snippet specifies which database to connect to and how to make a connection (host, socket, user, and password).
清单5显示了名为catalog的数据源的部分定义——指定连接的数据库以及如何建立连接(主机、套接字、用户和密码)的代码片段。
The connection is established to the remote host on TCP port 22.
建立到远程主机的TCP端口22的连接。
Connection attributes and corresponding host connection returned to the pool on disconnect.
连接属性和断开连接时返回给池的相应的主机连接。
Connection attributes and corresponding host connection returned to the pool on disconnect.
连接属性和断开连接时返回给池的相应的主机连接。
应用推荐