If you are connected to one partition and wish to retrieve the effective Settings for another partition, you must first connect to the new partition before invoking the table function.
如果您连接了一个分区并希望检索另一分区的有效设置，就必须在调用该表函数之前，首先连接这个新分区。
The sleep and tenacity Settings affect how the connector retries to connect to the database when the limit is exceeded.
睡眠和韧度设置将影响超过限制时连接器重新尝试连接到数据库的方式。
Mind that depending on the current authentication mode additional configuration Settings might be required for ETLDAP so it can connect to the TM1 server.
请记住，根据当前的身份验证模式，ETLDAP可能需要额外的配置设置才能够连接TM 1服务器。
Note: If some other authentication mode is used, ensure that all the proper settings are in place to allow ETLDAP to connect to TM1 server.
注意：如果使用其他身份验证模式，要确保所有设置都已经就位，ETLDAP 才能够连接TM1 服务器。
Do this by again clicking the Settings TAB, and expanding the Facebook connect section.
通过再次单击设置选项卡并展开Facebook联系区段完成这个操作。
It shows usage of this new connector and also some of the configuration property Settings required to be able to connect to IDS using JDBC artifacts.
它演示这种新连接器的使用方法，以及使用JDBC驱动程序连接IDS所需的一些配置属性设置。
If "failed to connect" errors do occur, then the Web server's Settings for the maximum number of listeners is too low and must be increased.
如果确实出现了“连接失败”错误，那么Web服务器的侦听器的最大数量设置太低了，您必须增加它。
The next collection of Settings specifies how to connect to your (debug) Web server.
下一组设置指定如何连接Web(调试)服务器。
Select the DB2 connection, and right-click on it to modify the connection in order to connect to the IBM DB2 UDB SAMPLE database. (See Figure 1 for my Settings.)
选择DB 2连接，右击它并修改连接，以连接到IBM DB 2UDBSAMPLE数据库(关于我的设置，参见图1。)
The settings for DB2 Connect are established through the DB2 catalog command.
DB2Connect的设置通过 DB2catalog命令建立。
Publishing improvements (developers can use a publish Settings file rather than having to connect to the Windows Azure portal).
发布过程的改进(Publishing improvements)(开发者可以使用发布设置文件，而无须连接到WindowsAzure门户)。
Cannot connect. Make sure your phone is turned on, or tap Settings to check your connection Settings.
无法连接。请确保电话已打开，或点击“设置”以检查连接设置。
Select Only selected client partition can connect in the Slot connection Settings area.
在Slotconnectionsettings区域选择Onlyselectedclientpartitioncan connect。
I have setup connection correctly and is able to connect to the PLC to configure its IP and various Settings.
我已经安装连接正确，能够连接到PLC配置其IP和各种设置。
Choose this option if you want to change the Settings Communicator USES to connect, for example if you change your ISP.
如果您想要更改通信器在连接时使用的设置，例如更改isp，则请选择此选项。
Choose this option if you want to change the Settings Communicator USES to connect, for example if you change your ISP.
如果您想要更改通信器在连接时使用的设置，例如更改isp，则请选择此选项。
应用推荐