The limit pressure angle is related to such factors as offset angle, mean spiral angle, pitch cone angle and mean pitch cone diameter, not to geometrical shape of the tooth surface.
极限压力角受偏置角、大小轮的螺旋角、节锥角和中点的分度圆直径影响，而与齿面的其他参数无关等结论。
If you're trying to check a 3d cone as a 2d dia at a certain Z level then, yes probe diameter will affect accuracy.
如果你尝试在其中特定z值平面内用一个2维测头测量一个3d立体圆锥体。那么探针直径将会影响精度。
The performance of different diameter cartridges of several explosives was obtained by tests in this paper, and their misfire diameters were also measured by cone charges.
试验得出了几种炸药在不同药卷直径下的性能结果，并采用锥形装药测定了炸药的熄爆直径。
STAND: Overall width of the assembled bearing; refers to the combination of sizes of the cone, outer diameter, cup, inner diameter, and roller.
座高：整套轴承的总宽度；参考内外圈尺寸，外径，内径以及滚子。
Ring's diameter increases as we move away from the apex of the cone.
诸圆环的直径自圆锥顶逐渐增大。
The linear measurement principle of flattened diameter of the ocular cornea and the location deviation of the cone prism which is used in the applanation tonometer are introduced.
介绍了用于压平眼压计的圆台压平棱镜进行角膜压平直径线性测量原理及定位偏差分析；
The diameter, width and loads of driving wheel and terrain cone index are considered.
方程考虑了驱动轮直径、宽度、垂直载荷和土壤圆锥指数值。
There are many factors influencing the bit diameter and the tooth row intermesh due to the complicated shapes of the main parts of a three cone bit.
三牙轮钻头主要零件形状复杂，影响钻头直径及牙轮齿圈啮合误差的因素较多。
There are many ways to measure base-level pitch diameter of cone-shaped thread.
检测圆锥管螺纹基面中径的方法有很多，但测量过程复杂。
Moreover, with the decrease of the cone waist diameter, more cladding modes are excited, and more interference peaks with enhanced intensity are observed.
锥腰直径减小，激发更多包层模，干涉峰个数增多，强度提升；
Small diameter cone bit positioning deflection by wire-line coring with steel ball supporting was used to solve the problem economically.
采用绳索取心钢球支撑小径锥面钻头定位偏斜技术对事故进行处理，经济有效。
When relative length or the slenderness ratio is the same, cavitation number becomes big as the conic angle or the diameter of the cone becomes big, as shown in Fig.
在相同的空泡相对长度或长细比下，随着锥顶角或直径的增大，对应的空化数也增大；
TIGHT IN CENTER : Condition of inner diameter of cone; inner diameter is not straight.
中心偏紧：出现在内圈的内径里，内径不是直的。
And a new method for calculating the diameter of thickening equipment with central feeding, such as, rake thickener, deep cone thickner, settling tower, thickening hopper etc, accord...
并应用其运动性状提出了计算耙式浓缩机、深锥浓缩机、沉淀塔和浓缩漏斗等中央给料浓缩设备的直径计算新方法。
The Reynolds number based on the cone base diameter is 50, 000.
基于圆锥体底部直径的雷诺数为50,000。
Tube caps include convex hull, hats, cone tube diameter changes, flat cover and tightening of design.
管帽包括凸形管帽、锥壳、变径段、平盖及紧缩口的设计。
The drill bit in a cone shape outside has an outer diameter larger than or equal to the drill barrel to form an outer bulge.
钻头外侧呈锥体形状，钻头外径大于或等于钻筒外径形成外凸。
The drill bit in a cone shape outside has an outer diameter larger than or equal to the drill barrel to form an outer bulge.
钻头外侧呈锥体形状，钻头外径大于或等于钻筒外径形成外凸。
应用推荐